Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Repeat the process with the other sleeve. . Fit the cover appliance over the top of the shirt ironer. The pocket goes on the back. . Fit the rubber tightener on the cover appliance into the guide on the lower frame of the shirt ironer. . To transport the ironer, hold the handle 10 Fig. 2 and tilt the appliance backwards. Transport the shirt ironer fully lowered to the place where you wish to store it! 29 Cleaning and maintenance Control panel and body of the appliance When necessary: . Use soapy water or a mild cleaning product. Dry with a soft cloth. Warning! Do not use solvents or abrasive detergents. Cleaning the ironing dummy When necessary or when the dummy is clearly dirty, the ironing dummy can be laundered together with your shirts. Use a mild detergent and a programme for delicate garments at 400 C. . Do not use fabric softeners or starch. . The ironing dummy can only be dried naturally (do not use a tumble drier). Warning! The ironing dummy cannot be ironed. Fit it straight back onto the shirt ironer when dry. The ironing dummy assembly consists of the cover material (outer ironing dummy) and the airbags. The airbags are located inside the outer ironing dummy and are attached to the frame independently. Warning! Allow the shirt press to cool down before removing the ironing dummy. Removing the ironing dummy . Close the flaps on the button band adjuster. . Remove the short sleeve button arm straps if necessary. . Remove the cuff adjusters by realising the snap fastener. . Completely loosen the adjustment cords on the bottom right-hand side of the ironing dummy. . Fully open the collar adjuster. . Open the collar support. . Lightly press the clip on the back of the head upwards. Fig. 16. . Remove the upper head section from back to front. 11, Fig. 2 . . Unlock the button band adjuster: Pull the unlocking ring upwards. Fig. 17. Warning! The button band adjuster tilts forwards. Support it with one hand. . Open the two adjustment cords in the head area, which is now accessible. Extract them from their guides. Fig. 18. . Open the cord fixture on the rear edge. Extract them from their guide. Fig. 19. On the front, the cord is fitted behind the button band and secured with the guides fitted for this purpose. . Turn the collar adjuster knob to its vertical position. . Grip the ironing dummy from the bottom and carefully pull upwards. . Pull the ironing dummy from front to back over the collar adjuster. Fig. 20. . You hold now the ironing dummy cover. Open the snap fasteners which join the sleeves of the ironing dummy to the airbags. The airbags are still on the frame and need to be removed: . Open the six snap fasteners on the shoulders, the snap fasteners in cross formation on the front and the snap fasteners around the left-hand tube on the front at the bottom. . Release the adjustment cord fixture at the bottom of the airbags. Extract them from the guide groove. The ironing dummy and the airbags can now be washed. Fitting the ironing dummy Make sure that nothing enters the air ducts which are now accesible. It is essential that the ironing dummy be fitted correctly in order to obtain optimum ironing results. 30 Cleaning and maintenance Be particularly careful when fitting the ironing dummy and follow all the instructions given. The ironing dummy should only be fitted when dry. First fit the airbags: . Each of the airbags (symmetrical) is joined with a strip. This strip is fitted on the front between the button band and the support tubes. The airbag with an extra section with 2 snap fasteners in the middle must be fitted on the left-hand side of the appliance (looking head on). . There are three snap fasteners on each side of the shoulder area which are fitted to the relevant airbag. . Fit the adjustment cords onto the round guides around the air-output grille and secure the cord fixture. Fig. 21. . Position the cross formation on the airbags and close the snap fasteners on the front at the bottom. Fig. 22. The extra section on the bottom left-hand side must be wrapped around the left-hand tube, protecting the hole on the tube in this area. . Check that the adjustment cords are secured properly. . Check that the airbags are positioned properly. . Start the “ cold” programme. The programme can be stopped at any time by pressing the “start/stop” button. . Check that the airbags are positioned properly. . Tighten any slack cords. . Correct any problems. . Fit the ironing dummy onto the upper part of the appliance with the button band still unlocked and the knob in its vertical position. . Fit the ironing dummy from back to front. There are 4 holes on the front of the upper part of the ironing dummy. The front adjustment cords are on this section. . When the dummy is fitted, set the knob to horizontal. . There are two guides on the head: front and back. . First fit the rear cord and then the front cord into the guides on the collar and secure. . The ironing dummy is joined to each airbag via an interior cord...
Эта инструкция также подходит к моделям:Утюги - TJ10500/02 (3.47 mb)