Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
. Check that all of the adjustment cords are secured properly. . Close the button band. It clicks into position. Check that the ironing dummy works properly: . Start the “ cold” programme. The programme can be stopped at any time by pressing the “start/stop” button. . Check that the ironing dummy is fitted properly. . Tighten any slack cords if necessary. . Correct any problems. . Fit the head section into the front guide. Click the front hook into the hole on the top part of the head. . Press the head section until it clicks into position. Fig. 28. . Position each of the cuff adjusters and close the relevant snap fasteners. 30 Cleaning and maintenance Cleaning the air filter Warning! All repairs or works on the appliance must be carried out by unplugged plug. . Clean the air filter more or less every six months. This period of time will vary depending on the specific conditions of the surroundings the appliance is used in. . Open the filter cover. . Extract the air filter. Fig. 29. . Clean it in plenty of hot water. If necessary, use a suitable commercial detergent. . Allow the air filter to dry. . Clean the filter support with a damp cloth. . Fit the air filter when clean and dry. . Close the filter cover. Before calling the Technical Service This shirt ironer complies with the safety guidelines established for electrical appliances. All repairs, modifications and work of any kind performed on electrical appliances must be carried out by Specialised Technicians. Incorrect repair work may result in damage to the appliance. However, consult the following list of simple faults which you may be able to solve yourself. If the following recommendations do not solve the problem, call our Technical Service! Problem Possible cause Solution The ironing programme does not start. The button has not been pressed. Press the button. The start/stop button has not been pressed. Press the start/stop button. The upper support is not correctly set to its upper position. Set the upper support to its upper position. The automatic fuse for the household circuit has been triggered. Connect/replace the automatic fuse. If the fault recurs, change from 16 amps to 10 amps. General electricity supply failure. Restart the programme when the electricity supply resumes. Reset the programme selector switch according to how dry the garment is. The plug is not plugged into the socket or is loose. Insert the plug firmly. 31 Before calling the Technical Service Problem Possible cause Solution Hot air in the “ cold” This is not a fault! Residual heat. The hot air disappears after a programme. short period of time. The Start / Stop The start/stop button has been pressed It stops after 30 seconds or light is flashing during an ironing cycle: pause function when start/stop is pressed. The ironing programme blows Indicates that the cycle is cold air for the last minute. finishing and the appliance has begun to blow cold air. Low air pressure in The ironing dummy has not been Fit the ironing dummy correctly. the ironing dummy. fitted properly. The air filter is dirty. Clean the air filter. Faulty ironing dummy. Replace the ironing dummy. Excessive air pressure The airbag is not fitted properly. Check the airbag adjustment in the ironing dummy. cords and adjust them correctly. No air pressure in the The ironing dummy arms are twisted. Set the arms in the right arms. position. The airbag arms are not inside the Insert the airbag arms in the ironing dummy arms. ironing dummy arms. Fig. 25. Ironing process too long. The 10 A version was used. Switch over to the 16 A version if possible. The ends of the The end of the cord has splipped into Press the button band adjuster adjustment cords used to the gap on the button band. in and pull on the cord. regulate size have become hooked up on the appliance. The fuse triggers when The wrong connection current has Select the right connection the appliance is been selected. current. See “Changing the connected. connection current”. You hear a noise on This is because the internal tube is This is not a fault and does raising or lowering the sliding not affect correct operation appliance. of the appliance. 32 Technical service and Warranty Technical service Warranty Should your appliance fail to work properly and all the instructions for use and installation (especially the section headed "Requirements....") have been carefully observed, then remember that our Technical Service Network is at your full disposal. When contacting the Technical Service, quote the model code (E-NR) and the appliance’ s factory number (FD). This information can be found on the characteristics plate, 17, Fig. 2. The conditions of warranty depend on the relevant Supplier in a particular country. Contact the establishment where you purchased your appliance for more information and quote the appliance model and factory number. The receipt of purchase for the appliance must be produced prior to any work carried out under warranty. Technical ...
Эта инструкция также подходит к моделям:Утюги - TJ10100/02 (1.37 mb)