Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
• Unplug the appliance from the mains supply after each use, or if a fault is suspected. • The electrical plug must not be removed from the socket by pulling the cable. • Never immerse the iron or steam tank in water or any other fluid. • Do not leave the appliance exposed to weather conditions (rain, sun, frost, etc.). 1Beforeusingtheironforthefirsttime Remove any label or protective covering from the soleplate. With the iron unplugged, fill in the tank of the iron with tap water and set the temperature control dial to “max” Plug in the appliance to the mains. When the steam iron has reached the desired temperature (pilot light switches off), start steaming by setting the steam regulator to the maximum steam setting and by repeatedly pressing the button . When using the steam function for the first time, do not apply it on the laundry, as there could stillbe dirt in the steam dispenser. When turned on for the first time, your new iron may smell and emit a little smoke and a fewparticles; this will stop after a few minutes. Howtousetheiron Check the recommended ironing temperature inthe label on the garment. •Synthetics •• Silk-Wool •••Cotton-Linen If you don’t know what kind or kinds of fabric agarment is made of, determine the right ironingtemperature by ironing a part that will not bevisible when you wear or use the garment. Start ironing the garments that require the lowestironing temperature, such as those made ofsynthetic fibres. Silk, wool or synthetic materials: iron the reverseside of the fabric to prevent shiny patches. ENGlISH (button) (button) B O S C H 13 FillingthewatertankFillingthewatertank (Model dependent) ENGlISH Set the steam regulator to the positionand unplug the iron from the mains! Use only clean water from the tap without mixinganything with it. The addition of other liquids, such as perfume, will damage the appliance. any damage caused by the use of theaforementioned products will make theguarantee void. Do not use condensation water from tumble dryers, air conditionings or similar. This appliancehas been designed to use normal tap water. To prolong the optimum steam function, mix tapwater with distilled water 1:1. If the tap waterin your district is very hard, mix tap water withdistilled water 1:2. To prevent spillage of water out of the appliancein vertical position, never fill beyond the “max” water level mark! Gettingready Remove any labels or protective coverings fromthe soleplate. 2Ironingwithoutsteam Set steam control to the position. 3Ironingwithsteam Only when the temperature dial is placed in theareas with the steam symbol. Set the temperature control to position : steam control to . Set the temperature control to position or “max”: steam control to . Tip : for better ironing results, iron the laststrokes without steam to dry the garment. The “e” steam setting (energy saving “e” setting: 24% energy saving*) can be used for mostfabrics. The steam settings should onlybe used on thick fabrics where there are still wrinkles. Steam setting eTemperatureSettingRecomendedSteamRegulatorSetting to “max” e and e *in comparison to the maximum steam setting of a regular 2400 Watt max Bosch iron Note: At a temperature setting of “•”, the soleplateis not hot enough to produce steam so the steamregulator should be set to the position to avoidwater dripping from the soleplate. 4Spray Do not use the spray function with silk. 5ShotofSteam Set the temperature control dial to at least the “•••” position Interval between shots of steam should be 5 seconds. 6verticalSteam Do not iron clothing while it is being worn! Never direct the steam at persons or animals! Set the temperature control dial to at least the “•••” position Operate the iron in a vertical position at adistance of 10 cm / 4 in, and press the button repeatedly with pauses of at least 5 seconds. Wait 10 seconds after each 4 shot cycle. 14 (button) (button) B O S C H 7Multipledescalingsystem8“SensorSecure”7Multipledescalingsystem8“SensorSecure” Depending on the model, this range is equippedwith the “AntiCalc” (=component 1 + 2 + 3). 1. self-clean Each time you use the steam regulator, the “selfclean” system cleans the mechanism of scaledeposits. 2. Calc’nclean The “Calc’nclean” function helps to removescale particles out of the steam chamber. Use this function approximately every 2 weeks, if thewater in your area is very hard. 1. Unplug the iron from the mains socket, set thesteam regulator to the position and fill the water tank with water. 2. Set the temperature selector to the “max” position and plug in the iron. 3. After the necessary warm-up period, thelamp goes out. Then, unplug the iron (veryimportant!). 4. Hold the iron over a sink. Press the “clean” button until approximately one third of the watercapacity of the tank is evaporated. Boilingwater and steam will come out, carrying scaleor deposits that might be there. 5. Release the “clean” button, and gently shakethe iron for some seconds, 6. Repeat the steps 4 and 5 three t...