Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If the tap water in your area is very hard, mix tap water with distilled water 1:2. You can inquire about the water hardness with your local water supplier. 45. 45. 45. 3 Setting the temperature The temperature control (J) adjusts the temperature of the soleplate (F). 1. Check the temperature instructions shown on the care label of the garment you are ironing and set the temperature control (J) to the corresponding position by lining it up with the pointer (H) on the iron: Fabric Temperature Setting Synthetics • Silk - Wool •• Cotton - Linen ••• ... .. ... ... .. 2. If you are unsure what type of material the garment is made from, start ironing on the lowest temperature setting and increase accordingly. If the garment is made from mixed fabrics, set the temperature for the most delicate material. 3. Sort your garments based on their care labels, always starting with clothes that have to be ironed at the lowest temperature. 4. The pilot lamp (L) will stay lit while the iron is heating up and go out once the selected temperature has been reached. Wait a few seconds after the lamp goes out before you start ironing. Once the iron is ready, you can continue to iron even if the pilot lamp comes on again. 5. If your iron is equipped with the auto shut-off function “secure”, the pilot lamp (L) will flash when the function has activated. Gently move the iron side to side to restart it 4 Ironing with steam The steam regulator (A) is used to adjust the amount of steam produced when ironing. 1. Make sure that there is water in the tank (I). 2. Adjust the temperature setting and then set the steam regulator according to the table below. Steam will automatically be produced: Temperature Setting Steam Regulator Setting ••• to “max” calc.n clean •• calc.n clean Note: At a temperature setting of “•”, the soleplate is not hot enough to produce steam so the steam regulator should be set to the position to avoid water dripping from the soleplate (F). 5 Ironing with shot of steam This can be used to remove stubborn wrinkles or to press in a sharp crease or pleat. It cannot be used on a synthetic setting for delicate items. 1. Set the temperature control (J) to the “•••” or “max” position. 2. Set the steam regulator (A) to the maximum position. 3. Press the shot of steam (C ) button on the handle repeatedly at intervals of 5 seconds. 6 Vertical steaming with shot of steam This can be used to remove creases from hanging clothes, curtains etc. It cannot be used on a synthetic setting for delicate items. WARNING! Do not vertical steam while the item is being worn. Never spray or aim steam at people or animals! 1. Make sure that there is water in the tank (I). 2. Set the temperature control (J) to the «•••» or «max» position and the steam regulator (A) to its maximum position. 3. Hold the iron in an upright position about 15 cm away from the garment being steamed. 4. Press the shot of steam button (C) on the handle at intervals of 5 seconds, however, after 4 jets of steam, wait for 10seconds to allow for continued steam production. 7 Ironing without steam This function enables the iron to be used for dry ironing. 1. Set the steam regulator (A) to the position. 2. Select an appropriate temperature for the type of material being ironed. 8 Spray This can be used to remove stubborn wrinkles. 1. Do not use the spray function with silk as staining may occur. 2. Make sure that there is water in the tank (I). 3. When ironing, press the spray button (B) and water will spray out of the spray outlet (E) onto the garment. 9 After finishing each ironing session 1. Unplug the iron from the mains socket. 2. Set the steam regulator (A) to the position. 3. Open the water tank cover (D). 4. Hold the iron with the point facing down and shake it gently until all the water has come out. 5. Set the iron aside in a vertical position to cool down. 6. Coil the power cable (K) loosely around the heel of the iron, before storing. 7. Store the iron in an upright position. 10 Multiple de-scaling system This range of irons is equipped with the following descaling features “AntiCalc”. A. self-clean Each time you use the steam regulator (A), the “self-clean” system cleans the mechanism of any scale deposits. B. calc’n clean The “calc’n clean” functi...
Эта инструкция также подходит к моделям:Утюги - TDA4626GB/01 (592.41 kb)
Утюги - TDA4633GB/01 (592.41 kb)
Утюги - TDA4650GB/01 (592.41 kb)