Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Maximum steam setting (w) for temperature settings 3 to MAX. • Water may leak from the soleplate if a too low temperature (2 or lower) has been selected. • For more details on how to switch on the iron, see the section headed “Setting the temperature”. Extra Steam 0 (types HI 225/226) (see table) • This feature provides extra steam to remove stubborn creases. • Apply Extra Steam only at 3 to MAX temperature setting. 7 -Set the steam control to the steam position w (fig. 6). -Press and hold the Extra Steam button (J) 0 (max. 5 seconds) (fig. 7). Then release the button. Wait at least 1 minute before applying Extra Steam again to prevent water from dripping out of the soleplate. Spraying T (types HI 215/216/225/226) (see table) -To remove stubborn creases from fabrics at any temperature, push the spray button T (C) a couple of times to damp the laundry (fig. 8). • Make sure there is enough water in the water reservoir. Self-cleaning 1 • The iron has a self-clean function to remove scale and impurities. • Use the self-clean function once every two weeks. If the water used is very hard, you should use the self-clean function more often. -Set the Steam control (B) to position O (fig. 2). -Set the temperature control dial (A) to MAX. -Fill the water reservoir (G) to maximum (MAX) level. -Plug in the iron to the mains, allow the iron to heat up. -When the amber pilot light (E) goes off, unplug the iron. -Hold the appliance horizontally over a sink (fig. 9). -Set the steam control to position 1 (self clean) (fig. 10). The steam control will then spring up slightly. -Pull the steam control up slightly (fig. 10). -Boiling water and steam will now come out of the holes in the soleplate. Impurities and scale (if any) are washed away with it. Move the iron forwards and backwards while this happens (fig. 11). -Repeat self-clean if a lot of impurities are flushed out. -You can pull the steam control further upwards to remove the steam control needle (fig. 12). It is then possible to remove any scale from the needle. For this purpose you may use vinegar. Avoid bending or damaging the steam control needle! -Replace the steam control needle. Insert the point of the needle exactly in the centre of the aperture and fit the small notch at the side into the spacing (fig. 13). -Press the steam control (fig. 14). -Set the steam control to position O (fig. 2). Do not put vinegar, starch, chemically descaled water or descaling agents in the water reservoir. 8 After self-cleaning - Plug the iron into the mains to dry up the soleplate. - When the amber pilot light (E) goes off, unplug the iron. -Move the iron gently over a piece of used cloth to remove water stains. Cool down the iron for storage. Cleaning -Before cleaning remove the mains plug from the wall socket and allow the iron to cool down sufficiently. -Scale and other stains can be wiped off the soleplate with a damp cloth and a non-abrasive (liquid) cleaner. Keep the soleplate smooth: avoid hard contact with metal objects. - The upper part of the appliance can be cleaned with a damp cloth. -From time to time clean the inside of the water reservoir by filling with water and shaking (fig. 15). Then pour the water back out (fig. 16). Storage -Remove the mains plug from the wall socket. -Pour any remaining water out of the water reservoir (fig. 16). -Set the Steam control (B) to position O (fig. 2). -Stand the iron upright and let it cool down sufficiently. -Wind the mains cord around the cord storage (fig. 17). -Always store the iron standing on its heel (fig. 18). -Always keep the iron in a safe dry place. Regularly check if the mains cord is still in a good and safe condition. Environment • Do not throw the appliance away with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this you will help to preserve the environment (fig. 19). 9 Polski Wazne Przed pierwszym uzyciem urzadzenia zapoznaj sie dokladnie z instrukcja jego obslugi i zachowaj ja na przyszlosc, do ewentualnej konsultacji. • Przed podlaczeniem urzadzenia upewnij sie, czy napiecie podane na tabliczce znamionowej jest zgodne z napieciem w sieci elektrycznej. • Podlaczaj urzadzenie wylacznie do gniazdka z uziemieniem. • Nie uzywaj urzadzenia jesli wtyczka, przewod sieciowy lub zelazko sa uszkodzone albo jesli zelazko spadlo z wysokosci lub przecieka. • Regularnie sprawdzaj, czy nie jest uszkodzony przewod zasilajacy. • Jesli przewod zasilajacy ulegnie uszkodzeniu, musi zostac wymieniony w autoryzowanym punkcie serwisowym firmy Philips lub przez osobe o podobnych kwalifikacjach, co pozwoli uniknac ewentualnego niebezpieczenstwa. • Nie pozostawiaj urzadzenia bez uwagi, gdy jest ono podlaczone do sieci. • Nigdy nie zanurzaj w wodzie zelazka i podstawki, jesli jest w nia wyposazone zelazko. • Przechowuj urzadzenie w miejscu niedostepnym dla malych dzieci. • Stopa zelazka moze byc bardzo rozgrzana i dotkniecie jej moze spowodowac poparzenia. • Nie po...
Эта инструкция также подходит к моделям:Утюги - HI226/02 (1.12 mb)