Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
1 litre). C Use tap water to fill the tank. . If the tap water in your area is very hard, we advise you to use 50% distilled water and 50% tap water. Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the steam tank. 4 Screw the cap tightly onto the filling aperture of the steam tank. Fast refill 1 Keep the appliance plugged into the mains and make sure the iron is on.Then set the steam tank switch to 'off'. C 2 3 Press the steam activator until you no longer hear any steam escaping from the appliance. C Keep the steam activator pressed in and slowly unscrew the cap of the steam tank by turning it anticlockwise.This will depressurise the steam tank. Make sure there is no steam left in the steam tank. Place a piece of cloth over the cap when unscrewing it. 4 5 Remove the mains plug from the wall socket. Fill the steam tank as described in section 'Filling the steam tank' and let the appliance heat up again. Setting the temperature Always place the steam tank on a stable, level and horizontal surface Do not put the steam tank on the soft par t of the ironing board. 1 Put the iron on the iron stand. Do not put the hot iron on the supply hose or the mains cord. Make sure the cord does not come into contact with the hot soleplate. 2 Set the required ironing temperature by turning the temperature dial to the appropriate position. C Check the laundr y care label for the required ironing temperature: ENGLISH Steam settingTemperature setting Symbol on laundry care label Type of fabric C B Synthetic fabrics (e.g. acetate, acr ylic, viscose, polyamide, polyester) and silk 1 MIN (see 'Ironing without steam') C Wool 2 Low to medium D Cotton, linen 3 Medium to MAX Z Please note that Z on the label means that the ar ticle cannot be ironed. If you do not know what kind(s) of fabric(s) an ar ticle is made of, determine the right ironing temperature by ironing a par t that will not be visible when you wear or use the ar ticle. Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. Star t ironing the ar ticles that require the lowest ironing temperature, such as those made of synthetic fibres. 3 Put the mains plug in an earthed wall socket and set both the steam tank switch and the iron switch to 'on'.The steam tank and the soleplate will now heat up. . The iron is hot enough when the temperature light goes out. . During steam ironing the temperature light goes on from time to time.This indicates that the iron is heating up to the right temperature. . If you have been ironing at a high temperature and subsequently set the temperature dial to a lower setting, wait until the temperature light goes on again before you continue ironing.This will prevent damage to your fabrics. Tips -If the fabric consists of various kinds of fibres, always select the temperature required by the most delicate fibre, i.e. the lowest temperature. For example: if an ar ticle consists of 60% polyester and 40% cotton, it should be ironed at the temperature indicated for polyester (1) and without steam. -When steam ironing woollen fabrics, shiny patches may occur.You can prevent this by using a dr y pressing cloth or by turning the ar ticle inside out and ironing the reverse side. -Velvet and other fabrics that tend to acquire shiny patches should be ironed in one direction only (along with the nap) while applying ver y little pressure. -Do not use steam when you are ironing coloured silk.This could cause stains. 10 ENGLISH Using the appliance Steam ironing C C 1 Make sure that there is enough water in the steam tank. . Steam ironing is only possible at higher ironing temperatures (temperature settings 2 to MAX). 2 Select a steam setting suitable for the selected ironing temperature: -Select steam setting MIN (no steam) for temperature setting 1 (see 'Ironing without steam'). -Select a low to medium steam setting for temperature setting 2. -Select a medium to MAX steam setting for temperature settings 3 to MAX. 3 The steam tank and the soleplate will now heat up. -Cold star t: the soleplate takes approximately 2 minutes to heat up and the steam tank takes approximately 8 minutes to heat up. -Quick reheat: if you refill the steam tank during the ironing process, the water in the steam tank will take approximately 6 minutes to heat up. 4 As soon as the water in the steam tank is hot enough for steam ironing, the steam tank power-on light goes out (GC6104, GC6103, GC6102 only).The steam-ready light goes on (GC6107 only). . During steam ironing the steam-ready light goes on from time to time. This indicates that the steam tank is being heated up to the right temperature. 5 Keep the steam activator pressed in while you are steam ironing. . If you want to use the steam function continuously, slide the steam activator lock to the locking position. 6 To stop steaming, release the steam activator lock. If you have not used the steam function for some time, the steam that was sti...
Эта инструкция также подходит к моделям:Утюги - GC6103/03 (1.44 mb)
Утюги - GC6106/03 (1.44 mb)
Утюги - GC6107/03 (1.44 mb)