Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
• Vertical Steam (Models 4042 & 4043 only) – Functions like a garment steamer to remove wrinkles from hung garments or drapes. • Longer Power Cord (Model 4043 only) – Provides 12 feet of power cord to give you added flexibility when ironing. • SHOT OF STEAM ® (Models 4042 & 4043 only) – Offers a powerful burst of steam for removing stubborn wrinkles. 3 your Learning EURO PRESS ™ Iron 1. Water Fill Hole 2. SPRAY MIST ® Button (Models 4041 & 4043 3. SHOT OF STEAM ® Button (Models 4042 & 4043 only) 4. Steam Dial 5. Power Indicator Light 6. Patented MOTION SMARTTM Auto-Off Indicator Blinking Light 7. 360° Tangle-Free Swivel Cord 8. Fabric Select Dial 9. See-Through Water Reservoir 10. Stainless Steel Soleplate 11. SPRAY MIST ® Release (Models 4041 & 4043 only) 12. Cord Wrap 0 7 10 9 8 4 5 6 2 3 1 11 12 4 your Filling the Water Reservoir You must fill the water reservoir the SHOT OF STEAM ® and SPRAY MIST ® features and to get steam out of your iron. Tip: SUNBEAM ® tests each iron at the factory to ensure that they function correctly. The test may leave a small, harmless amount of water within the water reservoir. Before you fill the water reservoir, please consider the following: • While this iron was designed for use with tap water, very hard water will reduce the performance of the iron. If your water is very hard, SUNBEAM ® recommends that you use tap water the first time, then consider using demineralized or distilled water for subsequent use. You should use tap water once a month, however, to maintain the iron’s optimal steam performance. • Do not use water that has passed through a home water softening system. This type of water contains minerals that will decrease the performance and shorten the life of your iron. Use demineralized or distilled water, instead. Important: When not ironing, always set the Steam Dial to ZERO and the Fabric Select Dial to MIN. To fill the water reservoir: 1. Make sure the iron is unplugged. Set the Steam Dial to ZERO and the Fabric Select Dial to MIN. 2. Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level. WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries. 0 0 5 ironing Ironing Dry Ironing 1. Make sure that the Steam Dial 2. Plug the cord into a 120 volt AC outlet. The Power Indicator will light. 3. Turn the Fabric Select Dial to the dry ironing fabric setting you desire and allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. Tip: Refer to the Ironing Guide on Page 15 for the recommended setting for your fabric. Steam Ironing 1. Follow the instructions for “Filling the Water Reservoir” on Page 5. 2. Plug the cord into a 120 volt AC outlet. The Power Indicator will light. 3. Turn the Fabric Select Dial to the steam ironing fabric setting you desire (Linen, Cotton, Wool or Silk) and allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. Tip: Refer to the Ironing Guide on Page 15 for the recommended setting for your fabric. 4. After the iron has heated (2 minutes), turn the Steam Dial to desired steam setting. 0 6 features Using the Iron’s Special Features SPRAY MIST ® (Models 4041 & 4043 The SPRAY MIST ® feature dampens the fabric in removing wrinkles from heavy setting creases. To use the SPRAY MIST ® feature: Press the SPRAY MIST ® button firmly. SHOT OF STEAM ® (Models 4042 & 4043 only) The SHOT OF STEAM ® feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water. To use the SHOT OF STEAM ® feature: Place the iron on top of the wrinkle and press the SHOT OF STEAM ® button each time you would like an extra burst of steam. The SHOT OF STEAM ® feature may be used continuously with just a short pause between shots. 7 Ironing features Vertical Steam (Models 4042 & 4043 The vertical steam feature to function as a garment steamer. Tip: When using the vertical steam on clothing, hang the clothing on a clothes hanger results. Hanging curtains and drapes may be steamed. To use the Vertical Steam: 1. Make sure that the iron has heated up (2 minutes). 2. Hold the iron in a vertical position, with the iron close to but not touching the fabric you want to steam. 3. With your other hand, pull the fabric tight. 4. Press the SHOT OF STEAM ® button at approximately 3-second intervals as you move the iron across the wrinkled area. WARNING: To prevent the risk of burns, keep your hand away from the area being steamed. WARNING: DO NOT steam garments while wearing them; this may result in injuries. 8 features Patented MOTION SMARTTM Auto-Off When the iron is plugged in, will light steadily, indicating that there is power to the iron. If y...
Эта инструкция также подходит к моделям:Утюги - 4041 (635.42 kb)
Утюги - 4043 (635.42 kb)