Оценок - , средний балл:
(
)
)
Производитель: Groupe SEB USA - T-FAL
Размер: 1.09 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
slow down the -Fill the water tank to maximum. scaling up of your -Set the iron on his heel, with the water tank full, and set the thermostat iron. to MAX -fig. 10. -When the thermostat light goes out, unplug the iron and hold it in a horizontal position, over a sink. -Remove the anti-calc valve. -Shake the iron gently, over the sink, until some of the water in the water Note! tank (with the impurities) has flowed out through the soleplate. The steam control -At the end of the operation, push the anti-calc valve back into position. position must -Turn the iron back on for 2 minutes, setting it on its heel, to dry the necessarily be on soleplate. STEAM in order -Unplug the iron, and when the soleplate is just warm, wipe it with a soft to remove or cloth. replace the iron's antiscale rod. 2. Cleaning the soleplate Attention! Your iron is equipped with a self-cleaning soleplate, which works by The use of a catalysis. scouring pad will Its exclusive active coating helps continuously eliminate all the impurities cause damage to generated by the normal day-to-day use of the iron. your soleplate's However, if you iron using an unsuitable programme, some traces may be self-cleaning left which require manual cleaning. In this case, it is recommended that coating -fig. 17 you use a soft damp cloth on the warm soleplate, in order not to damage the surface. Storing your iron -Unplug the iron and wait for the soleplate to cool down. -Empty the water tank and set the steam control to DRY . A little water may remain in the tank. -Wind the cord not too tightly around the heel at the back of the iron. -Store the iron on its heel. Environment Environment protection first !! Your appliance contains valuable materials which can be recovered or recycled. • Leave it at a local civic waste collection point. If there is a problem? Problem Possible causes Solutions • Water drips from the holes in the soleplate. • You are using the Shot of Steam button too often. • You have stored the iron horizontally, without emptying it and without setting it to DRY. • Wait a few seconds between each use of the button. • See the section "Storing your iron". • Brown streaks come through the holes in the soleplate and stain the linen. • You are using chemical descaling agents. • You are using pure distilled/demineralised or softened water. • Your linen is not rinsed sufficiently or you have ironed a new garment before washing it. • Do not add any descaling agents to the water in the water tank. • See section “Types of water not to use?”. • See section "Cleaning the soleplate" • Ensure linen is rinsed thoroughly to remove any soap deposits or chemicals on new garments which may be sucked up by the iron. • The soleplate is dirty or brown and can stain the linen. • You have ironed with an unsuitable programme (temperature too high). • You are using starch. • Select the appropriate program. Refer to the chapter “Clean the soleplate“ • Spray starch on the underside of the fabric to be ironed. • There is little or no steam. • The water tank is empty. • The anti-calc valve is dirty. • Your iron has a build-up of scale. • Your iron has been used dry for too long. • Fill it. • Clean the anti-calc valve. • Clean the anti-calc valve and carry out a self-clean. • Carry out a self-clean. • Wait for the soleplate to reach the correct temperature. • The soleplate is scratched or damaged. • You have placed your iron flat on a metallic rest-plate or ironed over a zip. • You have cleaned your soleplate with an abrasive or metal pad. • Always set your iron on its heel. • Try to avoid ironing over zips. • Refer to the chapter “Clean the soleplate”. • Water is leaking out through the water tank cover. • You have not closed the water tank cover properly. • Make sure the water tank cover has clicked shut. • Steam or water come from the iron as you finish filling the tank. • The steam control is not set to the DRY position . • Check that the steam control is set to the DRY position . • The spray and/or shot of steam do not work. • The water is empty. • Fill the water. • Water leaks out of the front of the iron. • You have exceeded the level MAX when filling the water tank. • Empty the surplus water out of the water tank. If you have any problem or queries, please contact our Customer Relations team first for expert help and advice. 845 602 1454 -UK (01) 677 4003 -Ireland or consult our website -Ref. 1800113017 • 05/2008 • Subject to modifications • JPM & Associes • marketing-design-communicati...
Эта инструкция также подходит к моделям:Утюги - FV9440 (1.09 mb)
Утюги - FV9430 (1.09 mb)