Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
• You are using steam while the iron is not hot enough. • You are using the shot of steam button too often. • The steam flow is too high. • You have stored the iron horizontally, without emptying it and without setting it to DRY. • You are using chemical descaling agents. • You are using pure distilled water. • Fabric fibres have accumulated in the holes of the sole plate and are burning. • Your linen is not rinsed sufficiently or you have ironed a new garment before washing it. • USING THE SELF-CLEANING FUNCTION : In order to extend the life of your iron, use the Self-Cleaning function once per month. - Unplug your iron and set the steam control on DRY . - Fill the water tank up to the limit (see recommendations for the types of water to use). - Leave water tank filler cover open until the end of the operation. - Place your iron on its heel and set the thermostat control on MAX. - Plug in your iron and wait until the thermostat light goes out. - Unplug the iron and hold it over a sink in the horizontal position. - Place the steam control on MAX. - Raise the anti-calc valve without removing it completely. - Shake the iron gently, over the sink, until all of the water in the water tank (with the impurities) has flowed out via the sole plate. -At the end of the operation, push the anti-calc valve back into position. -Turn the iron back on for 2 minutes, setting it on its heel, to dry the sole plate. - Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth. • CLEANING THE SOLE PLATE: -While the soleplate is still just warm, clean it by rubbing it with a moist, non-metallic pad. Recommendation : The self-cleaning function helps to delay the scaling of your iron. 4- STORING YOUR IRON - Unplug it and wait until the sole plate has cooled off. - Empty the water tank and set the steam control to DRY. - Store the iron on its heel. 3- MAINTAINING YOUR IRON (continued) GUARANTEE (U.K. ONLY) Details of the guarantee are shown on the guarantee card enclosed with the appliance.This guarantee does not affect your statutory rights. Should service or further information be required please contact the Tefal Customer Relations Department (see Helpline or enclosed Service Information leaflet). Do not attempt to dismantle the appliance yourself – this will negate the guarantee. In line with a policy of continuous product improvement,Tefal reserves the right to change product specifications without prior notice. Solutions • Restart the iron by lightly moving it. • Set the thermostat control to the required fabric to be ironed. • Set the thermostat in the coloured zone (from to MAX). • Wait until the thermostat light goes out. • Wait a few seconds between each use of the button. • Reduce the steam flow. • See the section "Storing your iron". • Do not add any descaling agents to the water in the water tank. • Do a self-cleaning and use tap water or 50 % tap water and 50 % demineralized water.. • Do a self-cleaning. • Clean the sole plate with a non-metallic sponge. Vacuum the holes of the sole plate from time to time. • Ensure linen is rinsed thoroughly to remove any soap deposits or chemicals on new garments which have been sucked up by the iron. • Clean the sole plate as indicated above. See the temperature table to correctly set the thermostat. • Clean the sole plate as indicated above. Always spray starch onto the reverse side of the fabric to be ironed. FOR YOUR SAFETY • Warning! The voltage of your electrical installation must correspond to that of the iron (220V-240V or 127 V depending on the model). Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee. • This iron must always be plugged into an earthed socket. • If using a mains extension lead, ensure that it is correctly rated (10A or 13A for UK only), with an earth. • If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger. • Never immerse your iron in water! • The appliance must be unplugged before filling or emptying the water tank. • If the appliance falls, have it checked by a professional before using it again; unseen damage may be dangerous. • The sole plate may be very hot: - Never touch it. - Always let it cool off before putting it away. - Never leave your iron unattended when it is plugged in or while the soleplate is still hot. - Always keep your iron out of the reach of children. • NEVER DISMANTLE YOUR IRON ; ALWAYS CONTACT AN APPROVED SERVICE CENTRE. This product has been designed for domestic use only. Any professional use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no resposibility and the guarantee will not apply. The mains lead is fitted with a BS 1363 13 A plug. If the plug supplied with the product is not suitable for your socket outlet, then it must be removed (cut off, if it is a moulded-on plug) and a suitable 3 pin plug fitted in accordance with the instructions...
Эта инструкция также подходит к моделям:Утюги - FV4030 (351.08 kb)