Войти:
Оценок - 4, средний балл: 4.3 ( )

Инструкция по эксплуатации Harbor Freight Tools, модель 66738

Производитель: Harbor Freight Tools
Размер: 809.49 kb
Название файла: 66738.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


A moment of inattention while operating tools may result in serious personal injury. Use personal protective equipb. ment. Always wear eye protection. Safety equipment such as fresh air mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Do not overreach. Keep proper c. footing and balance at all times. This enables better control of the tool in unexpected situations. Only use safety equipment that d. has been approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area. Tool use and care4. Do not force the tool. Use the a. correct tool for your application. The correct tool will do the job better and safer at the rate for which it was designed. Disconnect the plug from the powb. er source and allow to cool before making any adjustments, changing accessories, or storing this tool. Such preventive safety measures reduce the risk of damage or injury. Store idle tools out of the reach of c. children and do not allow persons unfamiliar with this tool or these instructions to operate the tool. Tools are dangerous in the hands of untrained users. Maintain tools. Check for misd. alignment or breakage of parts and any other condition that may affect the tool’s operation. If damaged, have the tool repaired before use. Many accidents are caused by poorly maintained tools. Service5. Have your tool serviced by a qualia. fied repair person using only identical replacement parts. This will ensure that the safety of the tool is maintained. Safety Warnings Maintain labels and nameplates on 1. the tool. These carry important safety information. If unreadable or miss ing, contact Harbor Freight Tools for a replacement. Place securely on Iron Holder (6) 2. when not in use. Keep away from flammable objects. 3. Do not overheat adhesive. 4. When using a handheld tool, maintain 5. a firm, controlling grip on the tool. Do not leave the tool unattended 6. when it is plugged into an electrical outlet. Unplug the tool from its electrical outlet and allow to cool down before leaving. This product is not a toy. Keep it out 7. of reach of children. Any power cord must be properly 8. grounded. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. WARNING: Handling the cord on 9. this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) The warnings, precautions, and in10. structions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Grounding To prevent electric shock and death from incorrect grounding wire connection: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a qualified service technician before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounded Tools: Tools with Three Prong Plugs Tools marked with “Grounding Re1. quired” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See 3-Prong Plug and Outlet.) The grounding prong in the plug is 2. connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See 3-Prong Plug and Outlet.) The tool must be plugged into an 3. appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the preceding illustration. (See 3-Prong Plug and Outlet.) Extension Cords Grounded1. tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet 2. increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.) The smaller the gauge number of the 3. wire, the greater the capacity of ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории