Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
To prevent damaging garments from too hot of an iron, it is best to first iron garments that require a low temperature. If you should need to switch from a high setting to a lower temperature, for example ••• Cotton to • Nylon, allow the iron about 5 minutes to reach the lower temperature. Tips: If you are unsure of a garment’s fabric content, start on a low setting and test the iron on an area of the garment that does not show, such as a seam. Gradually increase the heat setting until wrinkles remove without damaging the fabric. Sort out the garments to be ironed according to the type of fabric. This will minimize the frequency of temperature adjustment for different garments. To prevent shine, iron dark garments or those made of silk, acetate or rayon inside out. USING AS A DRY IRON The iron can be used on the dry setting with or without water in the reservoir. However, it is best to avoid having the reservoir too full of water while dry ironing. 1. Position temperature dial to MIN, lowest setting. 2. Turn the variable steam dial to O for no steam. 3. Stand the iron on its heel in an upright position on a heat resistant surface and plug into a 120V ~ 60 Hz outlet. 4. Turn the temperature dial clockwise to the desired setting. 5. When the ready light goes off, the iron has reached the desired temperature. 6. When finished, turn temperature dial to MIN, lowest setting and unplug. Allow the iron to cool before cleaning the exterior or storing. NOTE: During ironing, the ready light may cycle on again which indicates the iron is heating to maintain the proper temperature. CAUTION: If the iron is hot, DO NOT fill it with water. USING AS A STEAM IRON When using as a steam iron, be sure the temperature setting on the temperature dial is on the maximum steam setting ••• . Do not use any other setting for steam ironing. 1. Unplug the iron from the outlet. 2. Fill the water reservoir, see FILLING THE WATER RESERVOIR. 4 3. Stand the iron on its heel in an upright position on an iron-safe surface and plug into a 120V ~ 60 Hz outlet. 4. Turn the temperature dial to maximum position. 5. Allow approximately 1 minute for the iron to reach the desired temperature. The ready light will turn off. 6. Turn the variable steam dial clockwise for more steam and counter clockwise for less steam. Turn the variable steam dial to position for max steam. 7. When finished, turn temperature dial to MIN, turn variable steam dial to O and unplug iron. Allow iron to cool before cleaning the exterior of the iron or storing. CAUTION: Avoid coming in contact with escaping steam. BURST OF STEAM For a penetrating burst of steam to iron faster and to smooth difficult wrinkles, firmly depress the burst of steam button. Between the individual bursts of steam, pause for at least 3 seconds to let the iron reheat for maximum additional steam. SPRAY For a mist of water to moisten dry and difficult fabrics such as linen, cotton or wool, or to handle stubborn wrinkles, press the spray button. The spray function is also handy to moisten creases accidentally ironed into the fabric. The spray function can be used on any setting and does not affect the ironing temperature. NOTE: You may have to pump the spray button several times the first time you use the iron in order to start the spraying action. USING THE VERTICAL STEAM FUNCTION The vertical steam features allows you to eliminate wrinkles from drapes without having to take them off the rod or to freshen the appearance of clothing while on the hanger. 1. Unplug the iron from the outlet. 2. Fill the reservoir with water, see FILLING THE WATER RESERVOIR. 3. Position temperature control dial to MAX setting. 4. Stand the iron on its heel in an upright position on an iron-safe surface and plug into 120V ~ 60 Hz outlet. 5. Allow approximately 1 minute for the iron to reach the desired temperature. The ready light will turn off. 6. Hold the iron 7-15 inches away from the garment and press the burst of steam button once. 7. Wait a few seconds before pressing the burst of steam button again. The ready light will cycle on and then off during this process. Do not press the burst of steam button more than three times successively when ready light is ON. For best results, keep reservoir at least half full. 5 8. When finished, turn temperature dial to MIN, turn variable steam dial to O and unplug iron. Allow iron to cool before cleaning the exterior of the iron or storing. CAUTION: Avoid coming in contact with escaping steam. CLEANING STEAM VALVE 2. Dip the steam valve into white vinegar to dissolve calcium and mineral deposits. 1. Turn the variable steam dial counter-clockwise to the descaling position and pull out to remove from the iron. 3. Never use any sharp or rough objects to remove the deposits from the Steam Valve. 4. Rinse the steam valve with tap water. 5. Replace the variable steam dial in the descaling position and gently press down until in position. 6. Turn the variable steam dial to ‘O’ position. DO NO...
Эта инструкция также подходит к моделям:Утюги - 3342CAN (51.41 kb)