Оценок - , средний балл:
(
)
)
Производитель: Clam Corp
Размер: 638.78 kb
Название файла: d8a0e95f-7dd3-4755-9421-50d2aa263c85.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
. Instruction p/n 102477 -C l a m C ust o m e r S er vi ce I nf o r m at i o n - NOTICE!! Once used, this shelter cannot be returned to the store. If you have a warranty claim, have your sales receipt ready and contact Clam Corporation Customer Service by email inquiry or direct by calling: . Customer Service Hrs: -9am to 4pm, Mon. . Clam Corporation 600 Clydesdale Trail Medina, MN 55340 . Phone -763-231-4120 . Fax -763-231-4121 . Website – . Email – customerservice@clamcorp.com Clam Corporation cannot honor warranty without an original, dated receipt. Fri. Central Standard Time -P art s Li st --P art s Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 1 102496 BASE, GUIDE 08-09 1 2 101116 U-CHANNEL MOLDING 1 3 102172 CANOPY HOOP POLE 3 4 101069 CANOPY POLE 1/2" 6 101095 TOW ROPE, 3/8 DIA X 9 FT 1 6 102470 RIGHT PORCH GUIDE TUBE 1 6 102471 LEFT PORCH GUIDE TUBE 1 7 101118 LEFT CANOPY BRACKET 1 8 101119 RIGHT CANOPY BRACKET 1 9 101088 1/4-20X0.75" SCREW 16 102171 PORCH HOOP POLE 1 11 101083 TUBE SPACER CAP 8 12 101080 1/4-20 X 1.25" SCREW 8 13 101148 #6 X 0.38 SCREW 16 14 101081 1/4" WASHER 22 101082 1/4" LOCKNUT 30 16 102469 BENCH RAIL W/STRAPS 2 17 101230 1/4-20X2" SCREW 2 18 101208 1/4-20 X 1-1/2" SCREW 4 19 102459 BACK REST METAL TUBING W/ENDCAPS 1 102465 BACK REST CUSHION 1 21 102460 BENCH TUBE BRACKET W/ENDCAPS 2 22 102449 LEFT BENCH BRACKET 1 23 102464 BENCH CUSHION W/BUCKLES 1 24 102448 RIGHT BENCH BRACKET 1 102434 TENT, GUIDE 08/09 1 26 102477 MANUAL, 08/09 GUIDE 1 2 -P art s Di ag r a m --P art s Di ag r a m - 3 -P art s Di ag r a m --P art s Di ag r a m - 4 -St e p O n e --St e p O n e - 5 -St e p Tw o --St e p Tw o - 6 -St e p T hr e e --St e p T hr e e - 7 -St ep F o u r --St ep F o u r - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Feed the length of the porch hoop pole through the porch hoop sleeve sewn on the tent. Slide the porch hoop pole onto the porch poles, engaging the second hole position. Attach the porch velcro on each side of the tent. Guide Tent (p/n 102434) -St ep Fi v e - 8 To “set”the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the molding over the tent material and base lip. Continue pressing outward in both directions until you have secured about twelve inches of molding onto the base. Having temporarily secured the tent to the base, take a walk around the unit. Readjust the molding until you have verified the proper porch hoop pole position and also that the tent sides and corners are properly proportioned. When satisfied, continue applying the molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Use a side cutters to trim the ends of the molding if they are not equal relative to base. Reinstall the rear adjustable spreader pole to tighten the fit of the tent. If everything still looks good, secure the molding with the #6 phillips screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation. 6”6” IMPORTANT: Trim the edge of the molding so it ends approximately 6 inches behind the centerline seam on both sides of the shelter. -Ti p s f o r U se - 9 Folding and transporting your Fish Trap is easy: . Unsnap the rear spreader pole and lay it in the bottom of the base. .Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. .Cover with the Travel Cover* (an optional but recommended accessory to help prolong the life of the unit). Tow the unit out to your favorite fishing spot! (NOTE: continuous pulling behind an ATV or snowmobile may result in premature wear of the base. We recommend the optional Wear Strips* be mounted to the base of your Fish Trap). Make sure your Ice Shelter is completely dried out before storing for long periods of time. Store your Ice Shelter in a cool, dry place. Keep away from rodents. *See our accessory catalog or for these items and more! -S a f et y I nst r u ct i o ns - Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. .Do not use open flame heaters in your ice shelter. Injury or death may result from ...