Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
-8237 ( p / n 1 0 8 3 2 6 ) Specifications . Height – 75 ”(25 ”packed) . Width -75 inches . Depth – 90 ”(42 ”packed) . Weight -145 lbs . Instruction p/n 102483 -C l a m C ust o m e r S er vi ce I nf o r m at i o n - NOTICE!! -ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE A WARRANTY CLAIM, HAVE YOUR SALES RECEIPT READY AND CONTACT CLAM CORP. CUSTOMER SERVICE BY EMAIL INQUIRY OR DIRECT BY CALLING: ¦ Customer Service Hrs: -9am to 4pm, Mon. . u Clam Corporation 600 Clydesdale Trail Medina, MN 55340 .u Phone -763-231-4120 .u Fax -763 -231-4121 .u Email – customerservice@clamcorp.com .u Website – F r i . C e nt r a l S ta nd ard T ime CLAM CORPORATION CANNOT HONOR WARRANTY WITHOUT AN ORIGINAL, DATED RECEIPT. -P art s Di a g r a m ( S eat i n g ) – -P art s Di a g r a m ( S eat i n g ) – ITEM QTY P/N DESCRIPTION ITEM QTY P/N DESCRIPTION 8 101048 BLOCK, SLIDE 18 2 101813 BRACKET, RAIL HANGER 16 101081 WASHER, . FLAT 19 2 101817 BRACKET, FRONT SEAT 34 101082 LOCKNUT, .” THIN 20 6 101829 ASSY, STRAIGHT CANOPY POLE 8 101088 SCREW, .” X .” PHILLIPS 21 2 101830 ASSY, BENT CANOPY POLE 4 101146 ANGLE, 1-1/2”X 1-3/4” X 9” ALUM 22 2 101836 ASSY, FRONT SPREADER POLE 8 101147 SCREW, #10 x 1” LONG PHILLIPS 23 2 101839 ASSY, ROOF SPREADER POLE 2 101399 ASSY, SWIVEL PLATE 24 1 101840 ASSY, REAR SPEADER POLE 2 102430 BRACKET, REAR SEAT 25 1 102437 TENT, X2 8 101429 CAP, 1-1/8” DIA. TUBE 26 4 101863 ASSY, X2 CANOPY HOOP POLE 2 102512 CLIP, LATCH 27 2 101905 ASSY, FOLDING SEAT 2 101466 HAMMOCK, ACCESSORY 28 8 101906 SCREW, .” X 2-1/2”LONG PHILLIPS 16 101470 BOLT, .” HEX HEAD X .”LONG 29 1 102505 TUBE, 1” X 2” RECTANGULAR 2 101473 SCREW, 1/ 4” X 1-1/2”LONG PHILLIPS 30 1 101910 MOLDING, U-CHANNEL 8 101486 SCREW, .” X 1-3/4”LONG PHILLIPS 31 20 101938 SCREW, #8 PHILLIPS 4 101652 TUBE, SEAT RAIL 32 1 101095 ROPE 2 101810 BRACKET, X2 CANOPY 33 1 102483 MANUAL 08/09 X2 1 102500 BASE, X2 2 -Part s D i a g r am ( Sh e lt er ) --Part s D i a g r am ( Sh e lt er ) - 3 -St e p 0 ne --St e p 0 ne - 4 -St e p Tw o --St e p Tw o - 5 -St e p T hr e e --St e p T hr e e - 6 -St ep F o ur - Rear Seat Bracke t (p/n 102430) Latch Clip (p/n 102512) -St ep F o ur - Rear Seat Bracke t (p/n 102430) Latch Clip (p/n 102512) 7 -St e p Fi v e --St e p Fi v e - X2 Base (p/n 102500) 8 -St e p Si x --St e p Si x - 9 -St e p S e ve n --St e p S e ve n - 10 -St e p Ei ght --St e p Ei ght - X2 Tent (p/n 102437) 11 -St ep N i n e --St ep N i n e - 12 -St e p T en --St e p T en - 13 -Se a t i n g I nst a ll at i o n --Se a t i n g I nst a ll at i o n - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. With the latch clip hanging freely, tilt the complete assembly downward until the interior of the rear seat bracket surrounds the support tube. 14 -Se a t i n g I nst a ll at i on ( c o nt . ) --Se a t i n g I nst a ll at i on ( c o nt . ) - Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it into the two holes located above the horizontal slot of the rear seat bracket. WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE. FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS MOUNTING SYSTEM. Included is a tow rope for those not planning to install the optional tow hitch assembly (available for purchase at Two install the tow rope, drill two 1/2" holes in the sloped front of the base. Knot the ends of the tow rope after routing through the drilled holes. Tow Rope (p/n 101095) 15 -Ti p s f o r U se --Ti p s f o r U se - Folding and transporting your Fish Trap is easy: . Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the bottom of the base. .Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. .Cover with the Travel Cover* (an optional but recommended accessory to help prolong the life of the unit). Tow the unit out to your favorite fishing spot! (NOTE: continuous pulling behind a four wheeler or snowmobile may result in premature wear of the base. We recommend the optional Wear Strips* be mounted to the base of your Fish Trap). Make sure your Ice Shelter is completely dried out before storing for long periods of time. Store your Ice Shelter in a cool, dry place. Keep away from rodents. *See our accessory catalog or for these items and more! -S a f et y I nst r u ct i o ns - Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. .Do not use open flame heaters i...