Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Your Adjustable Bed has been totally engineered to provide you with reliability of operation and the strength you deserve. The manufacturer has given each bed a thorough inspection and testing prior to shipment. The utmost in comfort and safety has been provided for you. This bed is for HOME use only. It is NOT designed for hospital use and was not designed to meet hospital standards. Do not use bed with TENT TYPE oxygen therapy equipment, or near explosive gases. GROUNDING SAFETY This Adjustable Bed has a grounded plug (two flat blades and one round pin) as a safety feature to reduce the risk of electric shock. The plug will only fit into a grounded outlet one way. If this plug does not fit into your outlet, contact a qualified electrician and have them install a properly grounded outlet. NEVER REMOVE THE GROUNDING PIN OR ALTER THE PLUG IN ANY WAY. Unauthorized modifications could void the electrical portion of your warranty. The use of adapters is not recommended unless the outlet is checked by a qualified electrician to ensure the proper grounding of the adapter. Failure to use a properly grounded outlet for this product will compromise this important grounding safety feature and may result in electrical shock, electrical fire, or faulty operation of the product. FOR BEST RESULTS, YOUR BED SHOULD BE PLUGGED INTO A SURGE PROTECTOR (not supplied with this adjustable bed). WARNING! Do not open control box, motors or hand controls (with the exception of the battery compartment). The warranty is void if these units are tampered with. Any repair or replacement of adjustable bed parts must be implemented by an authorized person. IMPORTANT SAFETY FEATURE This Adjustable Bed is equipped with a special locking caster for your safety. In order to prevent the movement of this product, all four casters should be locked in position. This may be accomplished by pushing down the safety latch on the caster. To resume mobility of the product, lift up on the safety latch. You are strongly encouraged to place rubber caster cups or carpet squares under the casters in addition to locking them in place if the product is positioned on a hard surface floor such as hardwood, tile or linoleum. Although your casters are locked and will not roll, they may slide. Note: To avoid damage to flooring, casters must be installed before operating the bed. Failure to attach casters my void warranty. 1 WARNINGS For best performance, consumers should enter and exit the adjustable bed with the bed in the flat or down position. A note to consumers with pacemakers: As with any product that produces a vibrating motion, it is possible that some pacemakers may interpret this motion as a false sense of movement and/or exercise. This may or may not affect your pacemaker. If you have any concerns, please consult your physician. WEIGHT RESTRICTIONS: The recommended weight restrictions on our adjustable beds are as follows: Twin 300 Full 375 Queen 425 The bed will structurally support the recommended weights when distributed uniformly across the entire bed. This product is not desighed to support or lift this amount of weight in the head or foot sections alone. DO NOT SIT ON THE HEAD OR FOOT SECTION WHILE IT IS IN THE RAISED POSITION. Note: Exceeding the recommended weight restrictions could damage your adjustable bed and void your warranty. RADIIO FREQUENCY IS 310 MHz. WARNING: The transmitter and the receiver of the wireless control system have been tested and comply with FCC and DOC/MDC rules. Changes or modifications not expressly approved be the party responsible for compliance could void user’s authority to operate the equipment. 2 3 INSTALLATION STEP 2 Insert casters into the caster sockets at the bottom of each leg. If necessary, strike the center of the caster lightly with a hammer. NOTE: To avoid damage to flooring, casters must be installed before operating the bed. Failure to attach casters may void warranty. STEP 1 Remove and discard the packing materials from the bottom of the base unit. You will see the mattress retainer bracket and headboard brackets attached to the side rail of the bed. Remove these items and set aside for the moment. Remove bagged parts and the power cord from the underside of the bed. HEADBOARD BRACKET MATTRESS RETAINER BRACKET INSTALLATION STEP 3 Lift the base unit from the carton and, keeping the unit top-side-down, place it on a raised surface such as the mattress. Remove the four bolts at the foot end of the bed and attach the mattress retainer.. See Figure 1. The mattress retainer must be used or the mattress will slide off the end of the bed when the head is raised. If this product is not going to be attached to a headboard, omit Step 4 and Step 6. STEP 4 Attach the headboard brackets per instructions on Page 5. Brackets must be attached to allow a one inch space between the mattress and headboard (FAILURE TO FOLLOW THESE GUIDELINES MAY CAUSE THE HEADBOARD BRACKET TO INTERFERE WITH THE BASE FOAM WHEN THE HEAD SEC...