Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
Figure 12-1 Figure 12-2 14 Assembly Manual Assembly Step 13: Attach the Rear Cover Parts: • TreadClimber® Base and Treadle assembly from Step 12 • (1) Rear Cover Hardware: • (4) #10 Phillips Head Screws Figure 13-1 Tools: • #2 Phillips Head Screwdriver (included) 13-1 Attach the rear cover to the back of the frame with the (4) #10 Phillips Head Screws (2 per side) and the provided #2 Phillips Head Screwdriver (See Figure 13-1 and 13-2). Figure 13-2 Step 14: Attach the Drive Covers Parts: • TreadClimber® Base and Treadle assembly from Step 13 • (1) Left Plastic Drive Cover • (1) Right Plastic Drive Cover Hardware: • (6) #10 Phillips Head Screws Tools: • #2 Phillips Head Screwdriver (included) 14-1 Attach the left and right Plastic Drive Covers to the sides of the base with (6) #10 Phillips Head Screws (3 per side) and the provided #2 Phillips screwdriver (See Figures 14-1). Install upper screw first. Note: Do not tighten hardware until all screws have been installed. Figure 14-1 Assembly Manual Assembly Illustration 16-A: TreadClimber® Drive and Treadle Decals Treadle decal 1 per sideDrive decal 1 per side Figure 16-1 Step 16: Apply Decals Parts: • TreadClimber®BaseandTreadleassemblyfromStep15• (2)TreadleDecals• (2)DriveCoverDecalsTools: • #2PhillipsHeadScrewdriver(included) 16-1 Clean the application surface with a wet cloth and dry thoroughly with a towel. 16-2 Remove the backing on the decal. 16-3 Center the decal on the appropriate application surfaces (See Figure 16-1) for locations. 16-4 Rub the decal onto the surface to force out the air bubbles. Assembly Figure 15-1 Figure 15-2 Step 15: Attach the Side Foot Support Platforms Parts: • TreadClimber® Base and Treadle assembly from Step 14 • (1)LeftFootSupportPlatform• (1)RightFootSupportPlatformHardware: • (6)1/4”x1”FlatHeadScrewsTools: • 5/16”HexKey(included) 15-1 Attach the right and left side foot support platforms to each treadle with (6) 1/4” x 1” Flat Head Screws (3 per side). (See Figures 15-1 and 15-2.) Assembly Do not use or put the machine into service until the machine has been fully assembled 17-1 Inspect your machine to ensure that all fasteners are tight and inspected for correct performance in and components are properly assembled. accordance with the Owner’s Manual. Step 17: Final Inspection Be sure to record the machine serial number in the Owner’s Manual. Step 18: Attach the Power Cord 18-1 Make sure that the Power Switch is in the “Off” postition. 18-2 Carefully insert the power cord into the A/C inlet at the rear of the base unit (See Figure 18-1). NOTICE: Always plug cord into the base before plugging into the wall outlet. Note: The TreadClimber® machine plugs into any standard, grounded (three-prong) wall outlet. NEVER remove the grounding prong from the power plug and never use a two-prong adapter without a grounding wire. Figure 18-1 A/C inlet Power switch Assembly Manual Assembly Step 19:Verify (TC1000 only) or Calibrate (TC3000 & TC5000) Do not use the machine for exercise purposes without completing Calibration (TC3000/5000) or Speed Sensor Verification (TC1000). It is important to calibrate (TC3000/5000) or verify speed sensor operation (TC1000) after a power outage or after any electrical repair or replacement. Failure to follow this procedure prior to use could result in machine failure and could cause injury. Do not stand on the Walking Belts during calibration or speed sensor verification. During the entire process, stand on the side foot support platforms or beside the machine. Speed Sensor Verification (TC1000 only) 19-1 Insert yellow safety key, plug the power cord into a wall outlet, and turn on the red Power Switch at the rear of machine. (See Figure 19A.) 19-2 Standing to the left of the machine, activate the Start/ Stop switch. Belts should begin moving within a few seconds. 19-3 Allow belts to continue to turn for at least 15 seconds (elapsed time will be displayed on Console). If belts stop, note any error codes displayed on Console and turn power off at rear of machine. Contact customer service for assistance immediately at 1-800-605-3369. 19-4 Push FASTER button until SPEED display reads 1.5. Verify that belt speed increases and then holds constant at new speed. 19-5 Remove safety key. Belts should slow to a complete stop. 19-6 Replace safety key. Belts should remain stopped. 19-7 Push RESET button on Console. Your TC1000 is now ready to use. Review Owner’s Manual for operating instructions. NOTICE: If your TreadClimber® machine does not operate correctly as described in the above steps, do not use machine. Contact Customer Service for assistance immediately at 1-800-605-3369. Figure 19A Main Power Switch “On” SAFETY KEYFigure 19B TC1000 Faster Button 18 Assembly Manual Assembly Manual 19 Calibration (TC3000 & TC5000) Note: During calibration, observe the walking belt alignment. Belts do not need to be perfectly centered, but if they are far enough from center to cause a scraping sound, follow the Belt Alignmen...
Эта инструкция также подходит к моделям:Туристическое снаряжение - 1000 (4.06 mb)
Туристическое снаряжение - 3000 (4.06 mb)