Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to get the tent out. These actions may cut the shock cord and/or damage the pole ends. Raise the tent: • Unroll and unfold the tent and lay it on the ground. If it’s windy, stake down one front corner into wind. • Lay the poles side by side and divide according to length. 2 long for the tent, 1 long [ with gray section ] Hoop and 2 short for the fly. • Assemble the shock corded poles as you work. Try to keep the pole sections from snapping together, as this can damage the ends. Make certain each plain end has been properly seated into its metal ferrule. Slide the one tent pole through each sleeve. The poles should run from corner to corner and cross at the rear of the tent body. See fig 1. fig.1 fig.2 • Start at the rear of the tent and insert the post end of the poles into the web grommets. See fig.2. • At the opposite end, with the pole in one hand and the web in the other, feed the pole up, bending it evenly along its length to create an arc. Make sure the ferrules do not get caught on the sleeves. Place the post end into this grommet to maintain tension. Repeat with the other tent pole. See fig. 3. fig.3 • Stand the tent up and insert the hoop over the tent poles and through the front sleeve. Fit a post into the grommet on each side web. See fig. 4. Clip the fabric to the frame: • Working your way around the tent, attach all the clips to the poles. See fig. 5. Add the poles to the y: • Once the tent is securely staked, spread the rain fly out, top side down. Locate the pockets on the inside of the fly and insert the fly poles. See fig. 7. • Wrap the Velcro® strap around the center of each pole to secure in place. Stake down sequence: • The tent is now freestanding. Place it in your desired location and stake it down through the web loops. First, at the rear of the tent, stake down the ‘V’. Move to the front and stake down the section between the doors. Then go back to the rear and stake the corners. Lastly stake the front corners. It works best to do this before you add the fly. See fig.6. • We highly recommend that you attach the included guy lines and stake them out. Note: The guy lines take a unique path and twist through the second set of rings. See fig 12 & 13. Take down: Pull up stakes and open doors. Remove the fly. Push poles out of the sleeves. Collapse all poles and stow in the pole bag. Fold the tent/fly. Roll up both along with the pole bag towards a door. Stow all in the main bag. fig.10 fig.13 fig.11 fig.12 YOUR TENT IS READY! Rev A 6.09 fig.4 fig.7 fig.5 Good: 4 stakes /4 lines Best: 4 stakes /8 lines REV E. FEB 09 SEAM SEALING: We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor SeamGrip®. • Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. For example, seams that will be exposed to rain, runoff, or ground level water are a must for sealing, while seams on uncoated nylon or mesh panels don’t need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements. • Apply sealant to the inside and outside of all exposed seams. Several thin layers will work better than one thick layer. Read and follow manufacture's instructions. STAKING: All tents need to be staked down to keep them from blowing away. Securing the tent by placing heavy objects inside is just not adequate. • Once the tent body is erected, stake it out before the fly is put on. This enables you to square the tent up to ensure that the fly goes on properly and that the seams align with the frame. Pull the base of the tent taut between each web stake out loop or ring & pin. Make sure that all corners are square. It is important that you don’t stake the tent out too tightly. You will know it’s too tight, if the door zippers can not be easily operated. Drive stakes through the web loops, or with ring & pin, drive the stake just outside the ring so that the “J” hook catches it. Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent. • Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski poles, which are stuck in the snow...
Эта инструкция также подходит к моделям:Туристическое снаряжение - Suite 4 (6.47 mb)