Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• Select a level campsite clear of rocks, branches, and other hard or sharp objects, to install your tent. WARNING: Keep clear of overhead power lines. • Do not set up your tent under trees. • For best results in windy conditions, position end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Parts and Components Description Part Number Hub (1) 5010000120 Short Ridge Pole (2) 5010000121 Long Leg Pole (2) 5010000122 Short Leg Pole (4) 5010000123 Long Ridge Pole (4) 5010000124 Awning Pole (2) 5010000125 Rainfly (1) 5010000126 Hub (1) Short Ridge Poles (2) Long Ridge Poles (4) Long Leg Poles (2) Awning Poles (2) Short Leg Poles (4) To Set Up Tent 1. Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1) Fig. 1 Doors 2. Insert the two Short Ridge Poles (with sticker dots) into the sleeves (perpendicular to door) on top of tent. (Fig. 2) 3. Assemble four, shock- corded, Long Ridge Poles and insert into the four diagonal corner sleeves. (Fig. 2) Fig. 2 2 Short Ridge Poles with Dots 4 Long Ridge Poles 4. Insert end of first Short Ridge Pole (with dot) into flange with a dot on Hub (Fig. 3). Repeat for remaining Short Ridge Pole on opposite flange of Hub with a dot. NOTE: When installed properly, the loop on the bottom of the Hub will be parallel two Short Ridge Poles. Short Ridge Pole with Dot Hub Fig. 3 5. Insert four remaining Long Ridge Poles into Hub. (Fig. 4) Fig. 4 Tab NOTE: Make sure tab on each pole locks into slot on bottom of Hub. (Fig. 5) Tab on Pole Hub Fig. 5 Slot Tab Locked 6. Snap hook at top of tent onto metal loop on bottom of Hub. (Fig. 6) Fig. 6 7. Insert curved end of four Short Leg Poles into the four Long Ridge Poles on top of tent. (Fig. 7) NOTE: Make sure tab on each Long Ridge Pole locks into slot on each Short Leg Pole. 8. Insert curved end of two Long Leg Poles (with dots) into the Short Ridge Poles at front & back of tent. (Fig. 8) NOTE: Make sure tab on each Short Ridge Pole locks into slot on each Long Leg Pole. Fig. 8 Short Leg PolesShort Leg Poles Long Leg Pole (with Dots) Long Leg Pole (with Dots) (Front of Tent) 9. Raise tent by assembling shock-corded sections of each Long and Short Leg Pole and inserting into curved ends of Leg Poles. (Fig. 9) 10. Insert pin on loop at each corner and the front and back of tent into all six Leg Poles. (Fig. 10) 11. Locate both plastic hooks at each corner, and front and back of tent, then snap onto Leg Poles to attach. (Fig. 11) Fig. 9 Fig. 10 Pin & Loop on web tent strap FFig. 11 ig. 12 12. Drive stakes through rings, located on four corners and front and back of tent, at an angle for better anchoring. (Fig. 12) To Attach Rainfly 1. Drape Rainfly over tent. Make sure seams on Rainfly are facing down with web pockets and long straps centered over doors & back of tent. (Fig. 13) Fig. 13 Rainfly Long Strap 2. Locate and wrap hook and loop fasteners, on underside of Rainfly, and wrap around the Leg Poles to secure. (Fig. 14) Fig. 14 Hook and Loop Fastener (continued on other side) To Attach Rainfly continued 3. Insert end of Awning Pole with plastic tip into web pocket at front of the Rainfly. (Fig 15) 4. Insert metal tip on Awning Pole into hole in Long Leg Pole (Fig 16). NOTE: It may be necessary to rotate the pole slightly for proper alignment with Awning Pole. Fig. 15 Fig. 16 5. Install remaining Awning Pole at back of tent as shown in steps 3 & 4 above. (Fig. 15 & 16) 6. Insert hooks on elastic straps, located at corners of Rainfly, into holes on the four Short Leg Poles to secure. (Fig. 17) 7. Insert hooks on long elastic straps, located at front and back of Rainfly, into holes on Long Leg Poles to secure. (Fig. 18) Fig. 17 Fig. 18 8. Tie guylines onto the six web loops located on the sides of the Rainfly. (Fig. 19 & 21) 9. Loop end of guyline over stake, stretch tight, then hammer into ground at an angle as shown. (Fig. 20 & 21) 10. Secure door mat through loops with stakes. (Fig. 21) Fig. 19 Fig. 20 Web Loop Guyline Fig. 21Door Mat Attaching Room Divider 1. Divider Panel can be installed through center of the tent by inserting toggles through the top and bottom fabric loops as shown. (Fig. 22 & 23) Fig. 22 Fig. 23 Divider Panel Pockets for Gear Storage Overhead Storage 1. Hang the overhead storage panel by placing the hooks through the loops on the inside of the tent. (Fig. 24) NOTE: The overhead storage is to keep small items off the floor. Large or heavy items may damage the tent. Fig. 24 Hook on Storage Panel Tent Loop Electrical Cord Access 1. Unzip access panel in the lower left corner of tent and bring in electrical cord. NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 25) Fig. 25 Cooler Access The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler. 1. To use as a vent, unzip flap to expose screen. (Fig. 26) 2. To use ...