|
Фрагмент инструкции
Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. See owner’s guide for reference. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY! Place your treadmill on a level flat surface. It is recommended that you place a protective covering on your floor. PARTS • 1 Power Cord • 1 Safety Key • 2 Water Bottle Holders • 1 Hardware Pack (contents listed below) • Left and right outer Console Mast Covers TOOLS (included) • 5mm Allen Wrench/Phillips Screw Driver • Flat Wrench • 8mm Allen Wrench or 6mm Allen Wrench Note: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. If you have any questions, or if there are any missing parts, we will guarantee complete satisfaction. PLEASE CALL OUR TOLL-FREE DIRECT CUSTOMER ASSISTANCE CENTER @ 1-800-244-4192 Mon.-Fri., 8 a.m.-5 p.m. CST (excluding holidays). HARDWARE A) Linkage Arm C) Console Assembly Bracket 13mm nylon nut D) Console Mast Covers 16mm bolt 45mm bolt Quantity: 2 Quantity: 6 Quantity: 2 B) Console Assembly Bracket 40mm bolt Quantity: 2 7 1 2 A 1 2 A STEP 1: STEP 2: UNFOLD THE TREADMILL TO ITS SECURE AND TIGHTEN ALL BOLTS. UPRIGHT POSITION. 3 4 B C D STEP 3: STEP 4: ATTACH CONSOLE CABLE AND LOCK CON-ATTACH LEFT & RIGHT CONSOLE MAST SOLE INTO PLACE. SECURE AND TIGHT-COVERS/BOOTS. EN ALL BOLTS. Note: Do not pinch the wires. 5 STEP 5: PLACE WATER BOTTLE HOLDERS/STOPPERS & SAFETY KEY INTO CORRECT POSITION. IT IS NOW SAFE TO PLUG IN YOUR TREADMILL. 8 Assembly 2.1-5.1T ASSEMBLY UNPACKING Take caution when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. See owner’s guide for reference. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY! Place your treadmill on a level flat surface. It is recommended that you place a protective covering on your floor. PARTS • 1 Power Cord • 1 Safety Key • 1 Console Skirt • 1 Hardware Pack (contents listed below) • Left and right Console Mast Boots • Left and right Handle Bar (4.1T & 5.1T only) • Console Assembly • Left and Right Console Mast TOOLS (included) • 5mm Allen Wrench/Phillips Screw Driver • 8mm Allen Wrench or 6mm Allen Wrench Note: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. If you have any questions, or if there are any missing parts, we will guarantee complete satisfaction. PLEASE CALL OUR TOLL-FREE DIRECT CUSTOMER ASSISTANCE CENTER @ 1-800-244-4192 Mon.-Fri., 8 a.m.-5 p.m. CST (excluding holidays). HARDWARE A) 20mm Bolt B) 50mm Bolt C) Screw Quantity: 10 Quantity: 2 Quantity: 4 9 1 1 2 A Console Wire STEP 1: STEP 2: ATTACH CONSOLE MAST BOOTS TO THE ATTACH UPRIGHT SUPPORTS TO BASE LEFT & RIGHT UPRIGHT SUPPORTS. FRAME. SECURE AND TIGHTEN ALL BOLTS. Note: Do not pinch the wires. 3 4 B Console Wire STEP 3: STEP 4: SLIDE CONSOLE MAST BOOTS INTO POSI-ATTACH CONSOLE. SECURE AND TIGHTTION. EN ALL BOLTS. Note: Do not pinch the wires. 5 6 C A STEP 5: STEP 6: ATTACH CONSOLE SKIRT. SECURE AND ATTACH LEFT AND RIGHT HAND RAILS. TIGHTEN ALL BOLTS. Note: Step 6 is only for models 4.1T and 5.1T. 10 Treadmill Operation & Adjustment FOLDING Firmly grasp the back end of the treadmill. Carefully lift the end of the treadmill deck to the upright position until the foot lock latch engages and securely locks the deck into position. Make sure the deck is securely latched before letting go. To unfold, firmly grasp the back end of the treadmill. Gently press down on the foot lock latch with your foot until the lock latch disengages. Carefully lower the deck to the ground. Note: on some models the foot lock latch might be on the right hand side. Foot Lock Latch MOVING Your Horizon Fitness treadmill has a pair of transport wheels built into the base frame. To move, make sure the treadmill is folded and securely latched. Then firmly grasp the handlebars, tilt the treadmill back and roll. CAUTION! Our Treadmills are heavy, use care and additional help if necessary when moving. Do not attempt to move or transport treadmill unless it is in upright, folded position with the lock latch secured. Failure to follow t...
Эта инструкция также подходит к моделям:Тренажеры - ELITE 1.1T (2.13 mb)
Тренажеры - ELITE 3.1T (2.13 mb)
Тренажеры - ELITE 4.1T (2.13 mb)