Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
WARNING TOOLS INCLUDED PARTS INCLUDED 1 Safety Key1 Console Assembly (located under treadmill deck) 1 Power Cord4 Hardware Bags2 Handlebars2 Console Masts1 Bottle of Silicone LubricantREADING RACKWATER BOTTLE HOLDERGRIP PULSE HANDRAILSON/OFF SWITCHCIRCUIT BREAKERTRANSPORT WHEELAIR CELL POWER CORDCONSOLETOUCH PAD PANELFANSAFETY KEY PLACEMENTFOOT LOCK LATCHRUNNING BELT / RUNNING DECK SIDE RAILROLLER END CAPCONSOLE MASTREAR ROLLERADJUSTMENT BOLTSMOTOR COVER If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. For a complete exploded diagram, visit us at mm T Wrench 6 mm T-wrench10 mm L-wrench PRE-ASSEMBLY WARNING DO NOT ATTEMPT TO LIFT THE TREADMILL!* Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. Failure to do so may result in injury! Remove plastic wrap from console masts. Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. ASSEMBLY STEP 1 ASSEMBLY STEP 1 HARDWARE BAG 1 CONTENTS : FLAT WASHER (B) 20 mmQty: 1WAVY WASHER (F) 29 mmQty: 1BOLT (D) Qty: 1BOLT (A) 15 mmQty: 1TEFLON WASHER (C) 18 mmQty: 1FLAT WASHER (E) 27 mmQty: 1 TEFLON WASHER (C) FLAT WASHER (B) BOLT (A) LEFT CONSOLE MASTBOLT (D) MAIN FRAMELEFT LINKAGE ARMFLAT WASHER (E) WAVY WASHER (F) ELEVATION FRAME Open HARDWARE BAG 1. Cut banding straps. Do not move or lift treadmill from packaging. Move left linkage arm into position. Insert 1 bolt (A) and 1 FLAT WASHER (B) into left linkage arm followed by 1 teflon washer (C) and attach to elevation frame. Lift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on its own. Insert 1 bolt (D) and 1 FLAT washer (E) through left console mast followed by 1 WAVY washer (F) and attach to MAIN FRAME. ASSEMBLY STEP 2 HARDWARE BAG 2 CONTENTS : MAIN FRAMELOCK LATCH PIN (G) RIGHT FOLDING FRAME LOCK LATCH PIN (G) Qty: 1WAVY WASHER (F) 29 mmQty: 1BOLT (D) Qty: 1FLAT WASHER (E) 27 mmQty: 1 RIGHT CONSOLE MASTLEAD WIRECONSOLE CABLES A Open Hardware Bag 2. B Attach LOCK LATCH PIN (G) into RIGHT FOLDING FRAME using T-wrench and tighten completely. Pull LEAD WIRE through RIGHT CONSOLE MAST. After pulling the lead wire through the mast, the top of the console cable should be located at the top of the mast. Detach and discard lead wire. Continue step 2 on next page. ASSEMBLY STEP 2 (CONTINUED) FLAT WASHER (E) BOLT (D) RIGHT CONSOLE MASTMAIN FRAMEWAVY WASHER (F) ELEVATION FRAMECONSOLE CABLEPRE-ATTACHED BOLTFOOT LOCK LATCHRIGHT LINKAGE ARMPRE-ATTACHED NUTPRE-ATTACHEDTEFLON WASHER HARDWARE BAG 2 CONTENTS: LOCK LATCH PIN (G) Qty: 1WAVY WASHER (F) 29 mmQty: 1BOLT (D) Qty: 1FLAT WASHER (E) 27 mmQty: 1 Insert 1 bolt (D) and 1 FLAT washer (E) through RIGHT console mast followed by 1 WAVY washer (F) and attach to MAIN FRAME. Unscrew PRE-ATTACHED NUT and remove from RIGHT LINKAGE ARM and discard. Carefully move right linkage arm and PRE-ATTACHED TEFLON WASHER into position and attach to ELEVATION FRAME. Note: While holding RIGHT CONSOLE MAST in the upright position, tighten PRE-ATTACHED BOLT using T-wrench to attach RIGHT LINKAGE ARM. Cut band holding FOOT LOCK LATCH assembly. Lift the running deck until lock latch on side of treadmill is fully engaged. Remove console from box and place out of the way. Lower the treadmill running deck from the folded position by stepping on LOCK LATCH on lower right side. * Note: If you have attempted to move the treadmill from the box and the machine has sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position. 132 ASSEMBLY STEP 3 HARDWARE BAG 3 CONTENTS : FLAT WASHER (B) 20 mmQty: 4 SPRING WASHER (I) 15 mmQty: 4 BOLT (H) 20 mmQty: 4 FLAT WASHER (B) CONSOLE MASTCONSOLE CABLESPRING WASHER (I) BOLT (H) CONSOLE DO NOT ATTACHTHIS SIDE UNTIL STEP 3-D A Open HARDWARE BAG 3. B With running deck in lowered position, place console on the console masts. Align the brackets that are underneath the console with the top holes of the console masts. C To assemble the CONSOLE to the left CONSOLE MAST, insert 1 BOLT (H), 1 SPRING WASHER (I) and 1 FLAT WASHER (B) into the 2 holes in the left CONSOLE mast and lightly tighten. D Gently lift right side of the console to connect the console cable. Carefully tuck wire in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires. E Repeat step C above to assemble the right console mast to the console. INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN TREADMILL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY 13 ASSEMBLY STEP 4 SET SCREWS (J) HANDLEBARSCONSOLE HARDWARE BAG 4 CO...