Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
A Open hardware bag 2. B Align guide rail set with main frame as shown. C Attach the guide rail set to the main frame using 4 bolts (d), 4 flat washers (e) and 4 tooth washers (g). HarDWare BaG 2 CONTENTS : TOOTH WASHERS (G) FLAT WASHERS (E) GUIDE RAIL SET BOLTS (D) MAIN FRAME ce5.1, eX-58 SHoWn CE5.1 EX 58 EX 68 gS1050E TOOTH WASHER (G) 15 mm Qty: 4 FLAT WASHER (E) 17 mm Qty: 4 BOLT (D) 55 mm Qty: 4 9 10 EX-78 ASSEMBLY STEP 2 TOOTH WASHERS (G) FLAT WASHERS (E) GUIDE RAIL SET BOLTS (D) MAIN FRAME EX-78 ONL Y EX-78 * This step is for EX-78 models only. * CE5.1, EX-58, EX-68, GS1050E models skip to STEP 3. A Open hardware bag 2. B Attach the guide rail set to the main frame using 4 bolts (D), 4 flat washers (e) and 4 tooth washers (g). TOOTH WASHER (G) 15 mm Qty: 4 FLAT WASHER (E) 17 mm Qty: 4 BOLT (D) 55 mm Qty: 4 HARDWARE BAG 2 CONTENTS (For Steps A–B): 11 EX-78 ASSEMBLY STEP 2 SPRING WASHER (B) EX-78 15 mm Qty: 4 FLAT WASHER (I) 16 mm Qty: 4 BOLT (H) 35 mm Qty: 4 NUT (J) Qty: 4 GUIDE RAILS MAIN FRAME BOLTS (H) SPRING WASHERS (B) FLAT WASHERS (I) NUTS (J) C Attach the guide rails to the main frame using 4 bolts (h), 4 flat washers (i), 4 spring washers (b) and 4 nuts (j). HARDWARE BAG 2 CONTENTS (For Step C) : 12 ASSEMBLY STEP 3 ALL MODEL S EX-78 SHOWN BOLT (M) SPRING WASHER (B) FLAT WASHER (K) WAVY WASHER (L) PEDAL ARM CRANK PEDAL ARM WHEEL GUIDE RAIL CONSOLE MAST PRE-INSTALLED BOLTS CONSOLE CABLE MAIN FRAME Note : Be careful not to pinch any wires while attaching the console mast. A Open hardware bag 3. B Carefully pull the console cable through the console mast using the twist tie located inside the console mast. C Gently slide the console mast onto the main frame and attach console mast to main frame using pre-installed bolts. D Slide wavy washer (l) over crank followed by pedal arm as shown. Rest pedal arm wheel on guide rail. E Attach the pedal arm to the crank using 1 flat washer (k), 1 spring washer (b) and 1 bolt (M). F Repeat steps E–F on the opposite side of the elliptical. BOLT (M) 20 mm Qty: 2 SPRING WASHER (B) 15 mm Qty: 2 FLAT WASHER (K) 20 mm Qty: 2 WAVY WASHER (L) 22.5 mm Qty: 2 HARDWARE BAG 3 CONTENTS : 13 ASSEMBLY STEP 4 A Open hardware bag 4. B Silde 1 flat washer (N), 1 wavy washer (l) and another flat washer (N) onto the console mast. C Slide lower handlebar onto console mast and attach using 1 flat washer (N), 1 flat washer (k), 1 handlebar cap, 1 spring washer (b) and 1 bolt (M). D Repeat steps B–C on the opposite side of the elliptical. BOLT (M) 20 mm Qty: 2 SPRING WASHER (B) 15 mm Qty: 2 FLAT WASHER (K) 20 mm Qty: 4 WAVY WASHER (L) 22.5 mm Qty: 2 FLAT WASHER (N) 25 mm Qty: 6 EX-78 SHOWN HARDWARE BAG 4 CONTENTS : BOLT (M) SPRING WASHER (B) FLAT WASHERS (K) CONSOLE MAST FLAT WASHERS (N) HANDLEBAR CAP LOWER HANDLEBAR WAVY WASHER (L) ALL MODEL S 14 BOLT (O) SPRING WASHER (B) FLAT WASHER (E) FLAT WASHER (K) BOLT (M) NUT (J) LOWER HANDLEBAR SPRING WASHER (B) TEFLON WASHERS (P) LOWER LINK ARM PEDAL ARM BRACKET ASSEMBLY STEP 5 ALL MODEL S A Open hardware bag 5. B Slide lower link arm onto pedal arm bracket. C Attach lower link arm to pedal arm using 1 flat washer (k), 1 spring washer (b) and 1 bolt (M). D Align opposite end of lower link arm with bracket on bottom of lower handlebar. E Place teflon washers (P) on both sides of the lower link arm. While holding teflon washers (p) slide lower link arm into bottom end of lower handlebar. F Secure the joint with 1 flat washer (e), 1 spring washer (b),1 bolt (o) and secure with 1 nut (J). G Repeat steps B–F on the opposite side of the elliptical. BOLT (M) 20 mm Qty: 2 SPRING WASHER (B) 15 mm Qty: 4 FLAT WASHER (K) 20 mm Qty: 2 TEFLON WASHER (P) 28.4 mm Qty: 4 FLAT WASHER (E) 17 mm Qty: 2 NUT (J) Qty: 2 BOLT (O) 70 mm Qty: 2 HARDWARE BAG 5 CONTENTS : EX-78 SHOWN 15 EX-68 EX-78 GS1050E EX-68, EX-78 ASSEMBLY STEP 6 * This step is for EX-68, EX-78, GS1050E models only. * CE5.1 and EX-58 models skip to next page. A Open hardware bag 6. B Silde top cap and top cap rear cover over console mast and snap into place. C Slide console mast boot around console mast and insert into top cap. D Slide water bottle holder over console mast and attach using 3 bolts (R). EX-78 only: E Slide rear cap over rear stabilizer and attach using 2 screws (q). BOLT (R) 12 mm Qty: 3 EX-78 only: SCREW (Q) 15 mm Qty: 2 EX-78 SHOWN HARDWARE BAG 6 CONTENTS : WATER BOTTLE HOLDER CONSOLE MAST CONSOLE MAST BOOT TOP CAP BOLT (R) SCREWS (Q) REAR CAP (EX-78 ONLY) BOLTS (R) TOP CAP REAR COVER REAR STABILIZER 16 WATER BOTTLE HOLDER CONSOLE MAST CONSOLE MAST BOOT SCREW (S) SCREWS (S) TOP CAP CE5.1 EX-58 EX-58, CE5.1 ASSEMBLY STEP 7 * This step is for CE5.1 and EX-58 models only. * EX-68, EX-78, GS1050E models skip to next page. A Open hardware bag 7. B Silde top cap over console mast and snap into place. C Insert console mast boot over top cap and snap into place. D Slide water bottle holder over console mast and attach using 3 screws (S). HARDWARE BAG 7 CONTENTS : SCREW (S) 12 mm Qty: 3...
Эта инструкция также подходит к моделям:Тренажеры - EX-58 (4.39 mb)
Тренажеры - EX-68 (4.39 mb)
Тренажеры - EX-78 (4.39 mb)
Тренажеры - GS1050E (4.39 mb)