Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken. WARNING UNPACKING Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended that you place a protective covering on your floor. Note: It is recommended that you apply grease to the threads of each bolt as you assemble the product, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. Before proceeding, find your elliptical’s serial number located under the console mast boot and enter it in the space provided below. Also locate the model name which is located on the side cover. ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOxES BELOW: ........................3 ..............................3 ................................5 SERIAL NUMBER: MODEL NAME: * Refer to the SERIAL NUMBER and MODEL NAME when calling for service. * Also enter this serial number on your Warranty Card. 5 LIMITEDTROUBLESHOOTINGCONDITIONINGELLIPTICALBEFORE ASSEMBLY IMPORTANT INTRODUCTION WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN PRECAUTIONS INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES TOOLS INCLUDED 5mm Allen Wrench/Phillips Screw Driver 4mm Allen Wrench 17mm Flat Wrench PARTS INCLUDED 1 Console 1 Console Mast 1 Console Mast Boot 1 Stabilizer Tube 2 Upper Handlebars 2 Lower Handlebar Assemblies 2 Foot Pad Brackets 1 Power Supply 5 Hardware Bags If you have questions or if there are any missing parts, we will guarantee complete satisfaction. Customer Tech Support contact information is located on the back panel of this manual. GRIP PULSE WATERBOTTLE CAGE MOUNT CONSOLE MAST CONSOLE MAST BOOT MAIN FRAME PIVOTING FOOTPAD GUIDE RAIL CONSOLE UPPER HANDLEBAR H-BAR LOWER HANDLEBAR STABILIZER TUBE TRANSPORT WHEEL PEDAL ARM LINK ARM A S S E M B LY S T E P A) Open HARDWARE BAG FOR STEP 1. B) Attach STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A). A S S E M B LY S T E P 2 A) Open HARDWARE BAG FOR STEP 2. B) Extend the GUIDE RAILS away from the MAIN FRAME until bolt holes line up. C) Tighten BOLTS (A) to secure GUIDE RAILS. .................................................................................................................................................................. HARDWARE BAG FOR STEP CONTENTS : ...................................... HARDWARE BAG FOR STEP 2 CONTENTS : .................................................................................................................................................................. HARDWARE BAG FOR STEP CONTENTS : ...................................... HARDWARE BAG FOR STEP 2 CONTENTS : LIMITEDTROUBLESHOOTINGCONDITIONINGELLIPTICALBEFORE ASSEMBLY IMPORTANT INTRODUCTION WARRANTY & MAINTENANCE GUIDELINES OPERATION YOU BEGIN PRECAUTIONS .................. .................. .............. .................... ...................................................... .................................................. .............................................. ............................................................ INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 4 A) Open HARDWARE BAG FOR STEP 4. B) Attach the PEDAL ARM to the CRANK ARM using 1 NUT (D) and 2 WASHERS (E). C) Repeat on other side. .......................... .......... ............ .................... ............ .......................... .................. ............ HARDWARE BAG FOR STEP 4 CONTENTS : ASSEMBLY STEP 3 A) Open HARDWARE BAG FOR STEP 3. B) Slide the CONSOLE MAST BOOT over the bottom of the CONSOLE MAST. C) Carefully pull console wires through the CONSOLE MAST. Attach the console wires to the pre-attached routing wire. Discard wire when finished. D) Attach CONSOLE MAST using 3 LOCK WASHERS (C) and 3 BOLTS (B). E) Slide CONSOLE MAST BOOT down to cover exposed bolts. .................. ................................ .................................. ........................ .................... ................ .......... ............ .............................. ............ HARDWARE BAG FOR STEP 3 CONTENTS : A S S E M B LY S T E P 5 ............................5 ..........................( .................................................................................. A) Open HARDWARE BAG FOR STEP 5. B) Slide the LINK ARM into the PEDAL ARM. C) Place WAVY WASHER (G) over the LINK ARM axle. D) Attach FOOTPAD BRACKET to LINK ARM with 3 BOLTS (F). E) Repeat on other side. ...................................... HARDWARE BAG FOR STEP 5 CONTENTS : ..........................( ........N .......... ............................5 .......... LIMITEDTROUBLESHOOTINGCONDITIONINGELL...