Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly. Extra hardware may be included. 1" Tek Screw (83)–2 Extension Leg Nut (67)–2 Screw (3)–6 2.5" Extension Leg Bolt (65)–22.25" Extension Leg Bolt (92)–2 Handail Bolt (64)–4Front Endcap Screw (14)–2 1. Make sure that the power cord is unplugged. With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (58) so that the treadmill is more stable. Do not fully fold the Frame until the treadmill is completely assembled. Insert an Extension Leg (89) into the base of the Uprights (84). Hold an Extension Leg Nut (67) in the bottom of the Extension Leg, and thread a 2.25" Extension Leg Bolt (92) into the top of the Extension Leg. Next, thread a 2.5" Extension Leg Bolt (65) into the bottom of the Extension Leg. Firmly tighten the Extension Leg Bolts. Slide a Front Endcap (44) onto the base of the Uprights (84). Partially tighten a Front Endcap Screw (14) into the Front Endcap and the base. 89 58 44 84 92 14 67 1 65 6 7 3. With the help of a second person, carefully tip the treadmill onto its right side. Do not fully fold the treadmill until it is completely assembled. Insert the other Extension Leg (89) into the base of the Uprights (84). Hold an Extension Leg Nut (67) in the bottom of the Extension Leg, and thread a 2.25" Extension Leg Bolt (92) into the top of the Extension Leg. Next, thread a 2.5" Extension Leg Bolt (65) into the bottom of the Extension Leg. Firmly tighten the Extension Leg Bolts. Slide the other Front Endcap (44) onto the base of the Uprights (84). Partially tighten a Front Endcap Screw (14) into the Front Endcap and the base. 65 44 84 14 92 67 3 4. Attach two Base Pads (82) to the base of the Uprights (84) with two 1" Tek Screws (83). 84 83 83 82 82 4 89 2. Insert the tab on one of the Handrail Brackets (42) into the indicated slot in the right Upright (84). Attach the Handrail Bracket with a Screw (3). Slide a Handrail Cap (8) onto the lower end of a Handrail (20). Make sure that the Handrail Cap is oriented as shown. Insert the top of the Handrail (20) into the tube at the top of the right Upright (84), and slide the Handrail Cap (8) over the Handrail Bracket (42). Attach the top of the Handrail to the right Upright with two Handrail Bolts (64); start both Handrail Bolts but do not tighten them yet. Then, attach the Handrail to the Handrail Bracket with a Screw (3). Tighten the two Handrail Bolts. 2 Slot 42 20 84 3 8 64 3 5. Insert the tab on the other Handrail Bracket (42) into the indicated slot in the left Upright (84). Attach the Handrail Bracket with a Screw (3). Slide a Handrail Cap (8) onto the lower end of a Handrail (20). Make sure that the Handrail Cap is oriented as shown. Insert the top of the Handrail (20) into the left Upright (84), and slide the Handrail Cap (8) over the Handrail Bracket (42). Attach the top of the Handrail to the left Upright with two Handrail Bolts (64); start both Handrail Bolts but do not tighten them yet. Then, attach the Handrail to the Handrail Bracket with a Screw (3). Tighten the two Handrail Bolts. With the help of a second person, carefully raise the Uprights (84) to a vertical position. 6. Attach the Latch Housing (73) to the left Upright 6 (84) with two Screws (3); start both Screws and then tighten them. Note: Make sure that the large hole in the Latch Housing is on the indicated side. Locate the Latch Pin Assembly (21). Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert the pin into the Latch Housing (73). Then, tighten the knob onto the pin. See steps 1 and 3. Fully tighten the two Front Endcap Screws (14). 7. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the large hex key is used to adjust the walking belt (see page 20). 5 Slot 42 20 84 3 8 3 64 3 Pin Spring Collar Knob 73 84 Large Hole 21 If you purchase the optional chest pulse sensor (see page 17), follow the steps below to install the receiver included with the chest pulse sensor. 1. Make sure that the power cord is unplugged. Remove the indicated Screw (3) and the Access Door (76) from the back of the Console Base (85). 2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Base (85). Hold the receiver so the small cylinder is oriented as shown and is facing the Console Base. Attach the receiver to the plastic posts on the Access Door (76) with the two included small screws. 3. Make sure that no wires are pinched. Reattach the Access Door (76) with...