Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
WARNING! IMPORTANT!: Smaller holes (11/32"/ .87 cm) of top pole should face toward the front of the system and the warning label should be facing toward the front. 12 P/N 211789 02/04 4. 4. Secure tank struts (14) to pole as shown. Place cap (15) over exposed end of bolt as shown. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 10 11 11 45 14 3 15 Rotate non-secured ends of tank struts (14) outward to mounting holes in tank as shown. 14 14 13 02/04 P/N 211789 5. Secure ends of tank struts (14) to tank as shown. Repeat for opposite side. 43 11 22 11 14 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 6. Install upper pivot bracket (16) to front of base using bolt (19), washer (20) and nut (48) as shown. 48 20 16 19 14 P/N 211789 02/04 Insert bolt (21) through lower pivot bracket (17) as shown; bolt (21) will be secured during step 10. Carefully place base assembly on its side. Install lower pivot bracket (17) with bolt (23), washers (20), and lock nut (48) as shown. Secure both hinge tubes (18) to second wheel bracket (4) with carriage bolts (26) and flange nuts (22). 16 23 20 17 21 20 48 26 4 22 18 7. 8. IMPORTANT!: DO NOT OVER TIGHTEN 16 23 20 17 21 20 48 26 4 22 18 7. 8. IMPORTANT!: DO NOT OVER TIGHTEN 15 02/04 P/N 211789 Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using 9. pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet 7 6 5 4 6 7 SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT!: Position base as shown. Secure wheel bracket assembly with disc (64), washer (20) and nut (48) as shown. 21 64 20 48 Carefully reposition entire assembly as shown: 10. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT!: DO NOT OVER TIGHTEN 16 P/N 211789 02/04 17 02/04 P/N 211789 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD WRENCHES (2) 1/2”, (2) 3/4” AND (2) 9/16” This is what your system will look like when you’ve finished this section: Item #22 Item #37 Item #38 Item #39 Item #40 Item #41 Item #42 Item #46 Item #47 Item #48 (6) Item #58 Item #62 AND (1) 5/32 Allen Wrench Item #11 Item #31 Item #32 Item #28 Item #25 Item #44 (2) Item #24 Item #66 1/2”, 9/16”, 3/4" & EXTENSION AND/OR Item #63 1. 1. Securely rest the assembly on sawhorse. Install pole bracket (36) to top pole as shown (FIG.A) using bolts (38), metal spacers (63) and nuts (22). Reference finished assembly (FIG.B.) FIG.A 36 38 22 63 63 & 38 22 36 FIG.B COMPLETED ASSEMBLY TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 18 P/N 211789 02/04 FLAT SIDE TOWARDS BASE. 2. 2. Identify elevator tubes. Install triangle plates (33) and elevator tubes (35) to top pole section (1) as shown. Install pole cap (34) at this time. Toward 35 Toward Pole Board Upper & Lower Elevator tube 1 34 35 37 37 35 39 35 35 33 40 41 40 33 COMPLETED ASSEMBLY 39 39 19 02/04 P/N 211789 3. 3. Attach label (60) to window (27). Important: Line up top edge of label with top edge of window COMPLETED ASSEMBLY COMPLETED ASSEMBLY 60 27 4. Remove packaging materials and zip ties from handle assembly (30) Snap window into handle assembly (30) 30 20 P/N 211789 02/04 21 02/04 P/N 211789 5. Insert strut assembly (29) over inner channel (A) and between outer channel (B). Rest at angle shown in fig. A. Line up holes in strut bracket to holes in outer channel (B) 29 6. Insert metal spacer (22) through outer channel (B), strut bracket and inner channel (A). Center spacer on outer channel. NOTE: To allow spacer to fit through, lift inner channel (A) to help line up holes with outer channel (B). Strut bracket 44 30B 30A 29 30B 30A FIG. A 29 44 COMPLETED ASSEMBLY DO NOT REMOVE CLIP UNTIL SECTION F, STEP 1. THIS CLIP PREVENTS PREMATURE EXTENSION OF GAS STRUT. WARNING! IMPORTANT!: TO AVOID RAPID EXTENSION OF STRUT ROD - DO NOT DEPRESS BUTTON ON GAS STRUT ASSEMBLY. COMPLETED ASSEMBLY ORIENT STRUT ASSEMBLY SO CLIP-HANDLE FACES LONG SIDE OF CHANNELS 7. 7. Attach hook (59) to strip (61) 59 58 62 and secure with bolt (62) and nut (58). 61 8. Install hook and strip assembly into handle assembly. Bring strip through top of height indicator window 9. (27) underneath tabs and insert through bottom end of height indicator window (27). 61 61 IMPORTANT!: TO AVOID RAPID EXTENSION OF STRUT ROD - DO NOT DEPRESS BUTTON ON GAS STRUT ASSEMBLY. IMPORTANT!: STRIP(61) MUST PASS UNDERNEATH ALL 6 TABS OF HEIGHT INDICATOR WINDOW (27). TABS 61 22 P/N 211789 02/04 23 02/04 P/N 211789 35 11 10. Attach strut (29) to pole bracket (36) with bolt (31), washers (11), and nut (58) as shown. 11 58 11. Slip plastic spacers (25) onto metal spa...