Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Part No. Description 1 2 1 1 206646 200628 Tank (Black) Wheel Axle 3 2 226401 Wheel 4 1 1 908200 908246 Top Pole Section Middle Pole Section with Label 6 7 8 1 1 1 900644 203041 Bottom Pole Section Assembly Nut, Hex Flange, 3/8-16Net 9 1 201342 Wheel Bracket 11 12 13 14 16 17 2 4 1 1 1 1 2* 4* 201651 203104 206219 266001 203617 5E2356 203084 201344 Spacer, Wheel Axle Bolt, Hex-Flange 5/16-18 x 2" LongCapBolt, Carriage, 3/8-16 x 1.5 LongTank Cap Label, Moving System and Height Adjust. Bolt, Carriage, 5/16-18 x 1.75 LongKnob, Plastic, 3-sided 18 1 Rim 19 21 22 1 2 1 3 203470 900057 203795 203309 Washer, Flat 5/8 I.D. x 1-1/2 O.D. Backboard Mounting BracketNut, Special 3/8-NC Washer, .406 I.D. x 1.0 O.D. 23 24 26 2 2 4* 1 203053 200837 203100 900033 Bolt, Carriage 5/16-18 x 4Board Spacer Nut, Hex Flange, 5/16-18Slam Jam Bracket, Black 27 28 1 1 203796 200318 Bolt, “Tee” 3/8-NC x 5 Long Bracket Reinforcement, Slam Jam 29 1 1 203472 Spring, Black Backboard * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 5 12/05 ID# M611411 ID# M611411 12/05 6 PARTS IDENTIFIER- Actual Size 203041 NUT, HEX FLANGE, 3/8-16 #7 (1) #10 (2) #16 (2*) #13 (1) #22 (3) #25 (4*) #21 (1) #11 (4) #23 (2) #27 (1) #19 (1) PARTS IDENTIFIER- Not Actual Size #18 (1) #12 (1) #20 (2) #9 (1) #17 (4*) #14 (1) #2 (1) #1 (1) #3 (2) #8 (1) #24 (2) #28 (1) #26 (1) #29 (1) #30 (1) S SS E EE C CC T TT I II O OO N NN A AA : :: A AA S SS S SS E EE M MM B BB L LL E EE T TT H HH E EE P PP O OO L LL E EE S SS 1. Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 5 4 6 TOP MIDDLE BOTTOM Reference Stickers 7 12/05 ID# M611411 IMPORTANT! ONCE POLE SECTIONS ARE POUNDED TOGETHER- THEY CANNOT BE TAKEN APART 2. THE IDENTIFICATION STICKER IS LOCATED 3-3/4" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 2-1/2" MINIMUM OVERLAP, LEAVING 11/ 4" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5 4 4 5 6 Align poles using alignment marks. First, pound top and middle poles together by bouncing them on a scrap piece of wood on the ground as shown in FIG A. until they no longer move toward pole identification stickers. THEN add bottom pole section and pound together in the same way FIG B. FIG. A. FIG. B. IMPORTANT! HOLE DIMPLE 5" ID STICKER 1-1/2" TROUGH Wood Scrap (NOT SUPPLIED) ID# M611411 12/05 8 9 12/05 ID# M611411 SECTION B: ASSEMBLE THE BASE Install wheel axle (2) through wheel bracket (9) and install wheels (3) onto wheel axle (2) with spacers (10) as shown. Attach wheel carriage assembly to base (1) with bolt (13), washer (22), and nut (7) as shown. FINGER TIGHTEN - NO TOOLS REQUIRED. Assembly will be fully tightened in next step. 3. 4. 9 3 2 10 THE SPACER (10) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: BE SURE THAT THE SQUARE PORTION OF THE CARRIAGE BOLT (13) IS PROPERLY SEATED IN THE SQUARE CUT-OUT OF THE WHEEL BRACKET. IMPORTANT!: 1 13 7 22 ID# M611411 12/05 10 Attach pole assembly to tank assembly as shown. Secure pole assembly to tank and wheel bracket by turning the pole assembly clockwise as shown. Tighten pole completely and further rotate pole until struts are aligned correctly as shown in FIG B. 5. FIG B The pole should be turned approximately 7 complete rotations to tighten properly. When properly tightened, the wheel bracket will be tight against the base. An assistant is recommended to hold the base in place during this step. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT! 11 12/05 ID# M611411 22 16 17 6. Rotate struts down and bend struts outward to line up with holes on base as shown. Secure free ends of tank struts to tank with carriage bolt (16), washer (22), and knob (17) as shown. Repeat for other side. KNOBS MUST BE TIGHTENED COMPLETELY AND CHECKED PERIODICALLY FOR TIGHTNESS. WARNING! 7. 7. Mount brackets (20 & 26) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 10. NOTE: BOARD STYLE MAY VARY 2011242526272627 ID# M611411 12/05 12 13 12/05 ID# M611411 28 21 19 26 27 Install Slam Jam Rim to Backboard 18 19 21 A B D E A • Fit rim (18) securely into bracket (26) as shown (Allow "T"-bolt (27) to slip through center hole in rim (18). B • Install reinforcement bracket (28) onto “T” bolt (27) as shown. C • Install spring (29) onto “T” bolt (27) as shown. D • Install special nut (21) and washer (19) onto “T” bolt (27). E • Tighten nut (21) until flush with end of “T” bolt (27). 27 27 8. #28 29 27 C ID# M611411 12/05 14 XSHBM01.EPS 211208 SAWHORSE OR SUPPORT TABLE 9. Support pole and tank assembly over support table. Carefully slide backboard components onto pole. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WA...