Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Part No. Description 15 2 203470 Washer, Flat, S/J 16 2 203472 Spring 17 2 203795 Nut, 3/8-16 Special S/J 18 2 203796 T-bolt, 3/8-16 x 5" 19 3 203798 Bolt, Hex 5/16-18 x 1.5" 20 3 204290 Net 21 2 Rim 22 2 ** 207103 Pole Cap, 3.5" 23 2 900033 Bracket, S/J 24 1 FR908359 Pole, 2.75" 25 1 909271FR Board, 44" Rectangular, Ball on Court 26 1 919246FR Board, 44", Traditional NBA, Brown 27 1 979281FR Board, 50" Polycarbonate, Blue ** EXISTING COMPONENTS HARDWARE IDENTIFIER (Bolts and Screws) Item #7 (8) Item #18 (2) Item #19 (3) Item #2 (2) Item #8 (4) HARDWARE IDENTIFIER (Nuts, Washers & Springs) Item #17 (2) Item #9 (8)Item #11 (10) Item #16 (2) Item #15 (2) Item #14 (4) 3 11/06 ID# M890031 Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). CORNER4CORNER3Open - No Board 3-1/2" 65246CA 3" 66281CA 77271CA 3-1/2" 3-1/2" CORNER1CORNER2 Display boards will be mounted as follows: Corner Location 1: 66281CA • 50” Polycarbonate Backboard • Blue Graphic • Black Slam Jam Rim • Use extension arm for assembly Corner Location 2: 77271CA • 44” Rectangle Recycled Board • Basketball on Court Graphic • Black Slam Jam Goal • Use extension arm for assembly Corner Location 3: 65246CA • 44” Trapezoidal Recycled Board • Evolution Logo • Black Standard Goal • Gooseneck Pole System Corner Location 4: Open - No Board ID# M890031 11/06 4 A At corner location 3: remove the current 3" display pole from the mounting stub. CORNER1CORNER2Corner Location 3: REPLACE POLE A At corner location 3: remove the current 3" display pole from the mounting stub. CORNER1CORNER2Corner Location 3: REPLACE POLE 1. B Then, still at corner location 3, slide the 2.75” diameter pole end of the display pole (24) inside the moiunting stub. Secure the display pole by sliding the display wedges (12) into position as shown. To lock the display pole in place, tighten the hex-bolts (19). CORNERCORNER41CORNERCORNER23 5 11/06 ID# M890031 24 24 12 19 12 12 19 19 Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY 1. 27 7 23 Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23), extension arm (10) and mounting spacers (4) assemblies to backboard using bolt (7 ) and nut (11) as shown. Display Stand - Top View 11 18 4 4 1011 CORNERCORNER41CORNERCORNER2366281CA 3-1/2" Open - No Board 3-1/2" 77271CA 3-1/2" 65246CA 3" 2. 27 9 13 Attach board assembly to pole. ** (Use existing extension arm (9) and pole cap (22) on current display). 22 TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 9 9 ID# M890031 11/06 6 3. 3. • Fit rim (21) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). Tighten nut (17) until flush with end of "T" bolt (18) as shown here. NOTE: 1 17 15 16 21 23 18 Peel protectivefilm from surface of acrylicbackboard prior to use. NOTE: 4. Install net (20) as shown. OUTSIDE VIEW A. 21 20 7 11/06 ID# M890031 ID# M890031 11/06 8 Corner Location 2: 48” SQUARE MOLDED PLASTIC BOARD ASSEMBLY 1. Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23) and extension arm (10) to backboard using bolt (7) and nut (11) as shown. Tighten completely. 25 23 11 7 18 10 18 25 9 9 9 13 2. Attach board assembly to pole. ** (Use existing extension arm (9) and pole cap (22) on current display). TWO CAPABLE ADULTS 22 REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 7 CORNER CORNER 4 1 CORNER CORNER 2 3 66281CA 3-1/2" Open - No Board 3-1/2" 77271CA 3-1/2" 65246CA 3" Display Stand - Top View 3. • Fit rim (21) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 1 17 15 16 21 Tighten nut (17) until flush with end of "T" bolt (18) as shown here. NOTE: 1 17 15 16 21 Tighten nut (17) until flush with end of "T" bolt (18) as shown here. NOTE: 23 18 21 4. Install net (20) as shown. 20 9 11/06 ID# M890031 ID# M890031 11/06 10 1. Corner Location 3: 44" TRAPEZOID MOLDED PLASTIC BOARD ASSEMBLY Display Stand - Top View Attach rim (6), backboard (26) and support brackets (3) to the mounting pad on the top pole using the bottom rim mounting bolts (8) as shown. 3 6 8 8 3 26 CORNER CORNER 4 1 CORNER CORNER 2 3 66281CA 3-1/2" Open - No Board 3-1/2" 77271CA 3-1/2" 65246CA 3" 11 11/06 ID# M890031 Install the top rim mounting bolts (8) as shown. 6 26 8 2. Install support bracket mounting bolts (21) as shown. 26 6 11 11 2 2 3. 4. OUTSIDE VIEW B. C. D. A. 21 20 Install net (20) as sho...