Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
7 Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 8 7 6 8 46 5 10 P/N 214994B 05/03 10 6 7 8 6. 2 28 28 3 3 9 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! THE SPACER (28) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: 10 6 7 8 6. 2 28 28 3 3 9 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! THE SPACER (28) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: 11 13 1 14 13 12 12 7. Secure tank struts (13) to pole. Rotate non-secured ends of tank struts (13) outward to mounting holes in tank as shown. TIGHTEN BOLT (11) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 11 05/03 P/N 214994B 8. 13 13 1 Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. 13 17 12 12 16 8. 13 13 1 Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side. 13 17 12 12 16 12 P/N 214994B 05/03 SECTION B: ASSEMBLE THE BOARD AND RIM This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) Item #19 (12) Item #17 (6) Item #21 (4) Item #22 (4) Item #23 (2) 1/2” 1/2” AND/OR 13 05/03 P/N 214994B 1. 1. Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 3 of this section IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. 21 22 22 18 20 17 17 Refer To Instructions Included With Rim Hardware For Rim Assembly. 14 P/N 214994B 05/03 2. SAWHORSE OR SUPPORT TABLE Support pole and tank assembly over support table. Carefully slide backboard components onto pole. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! Support pole and tank assembly over support table. Carefully slide backboard components onto pole. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! 5 24 23 3. While still in the horizontal position, carefully slide backboard components onto pole. Secure hardware at desired position as shown and tighten all hardware completely at this time. 15 05/03 P/N 214994B 4. Install clips. CLIP “ARM” CLIP “BODY” USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. WARNING! 19 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping. A AA B BB C CC 18 16 P/N 214994B 05/03 NET INSTALLATION Insert net into bottom of clip as shown. SIDE VIEW NET NETCLIP 9. 18 19 25 SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP 17 05/03 P/N 214994B SECTION C: APPLY HEIGHT AND MOVING LABEL & SECURING SYSTEM 15 1. 10 feet (3.05 m) Carefully upright assembly. Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! 2. 30 29 27 29 Place assembled unit to desired location. Fill tank with water (30 gallons (114 liters)) or sand (360 lb. (163 kg)) and snap tank cap (30) in place. Insert T-strap (29) through slot on back of base as shown. Secure unit to ground by twisting tie down stake (27) into ground and hooking T-strap (29) onto tie down stake (27). 29 18 P/N 214994B 05/03 Equipement de basketball portable avec systeme d'elevation - Manuel de l'utilisateur Une Entreprise Huffy NOTEZ ICI VOTRE NUMERO DE MODELE:___________ Customer Service Center • N53 W24700...