Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer, to prevent loos- ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. 5STEP1STEP3STEP4STEPX6000DA X6200HRC/DA 2STEP dual-action elliptical trainers TOOLS & HARDWARE INCLUDED 5 5 MM Allen Wrench 13 13 MM Wrench Screwdriver 5 5 MM L-Shaped Wrench 19 19 MM D x 440MM L Rear Folding Axle Quantity: 1 (not shown to scale) M8 x 80MM Bolt Quantity: 4 M8 x 13MM Nylock Nut Quantity: 4 M8 x 45MM Bolt Quantity: 2 BLUE BAG BLACK BAG M8 x 16MM Bolt Quantity: 4 3 GREEN BAG M7 x 35MM Bolt Quantity: 2 M8 x 12MM Bolt Quantity: 2 M8 x 25 x 1.5T Washer Quantity: 2 M16 x 22 x .3T Spring Washer Quantity: 2 M26 x 34 x .3T Spring Washer Quantity: 2 M8 x 35 x 2T Washer Quantity: 2 M8 x 13MM Nylock Nut Quantity: 4 13MM Nut Caps Quantity: 2 ORANGE BAG M8 x 16MM Bolt Quantity: 2 16 x 22 x .3T Spring Washer Quantity: 2 5/16” x 30 x 1.5T Washer Quantity: 2 M5 x 25MM Bolt Quantity: 1 M8 x 60MM Bolt Quantity: 2 16 x 28 x 1.5T Washer Quantity: 2 8 x 15 X 2T Lock Washer Quantity: 4 8 x 17 X 1.5T Washer Quantity: 2 PINK BAG M8 x 12MM Bolt Quantity: 2 GREEN BAG M7 x 35MM Bolt Quantity: 2 M8 x 12MM Bolt Quantity: 2 M8 x 25 x 1.5T Washer Quantity: 2 M16 x 22 x .3T Spring Washer Quantity: 2 M26 x 34 x .3T Spring Washer Quantity: 2 M8 x 35 x 2T Washer Quantity: 2 M8 x 13MM Nylock Nut Quantity: 4 13MM Nut Caps Quantity: 2 ORANGE BAG M8 x 16MM Bolt Quantity: 2 16 x 22 x .3T Spring Washer Quantity: 2 5/16” x 30 x 1.5T Washer Quantity: 2 M5 x 25MM Bolt Quantity: 1 M8 x 60MM Bolt Quantity: 2 16 x 28 x 1.5T Washer Quantity: 2 8 x 15 X 2T Lock Washer Quantity: 4 8 x 17 X 1.5T Washer Quantity: 2 PINK BAG M8 x 12MM Bolt Quantity: 2 5 STEP1 • Install the left and right stabilizers with the four bolts (M8 x 16MM), using the Blue 5MM Allen wrench. • Cover both stabilizers with the included rubber boots. • Insert the rear folding axle shaft (440MM L x19MM D) into the rear tube. BLACK BAG STEP1 STEP2 • Slide a spring washer (M16 x .3T) onto the right-hand side of the rear folding axle, followed by the righthand pedal arm guide rail (the guide rails each have a blue indicator arrow printed on their sides; these arrows should face to the outside). • Slide a flat washer (M16 x 1.5T) onto the right-hand side of the rear axle, followed by a rear wheel. • Slide the large flat washer (5/16” x 1.5T) onto the right-hand side of the rear axle, and secure with a bolt (M8 x 16MM). • Repeat above steps to install lefthand pedal arm guide rail. ORANGE BAG STEP2 STEP3 STEP3 • Mount the rear pedal arms to the front pedal arms using four bolts (M8 x 80MM) and four 13MM NyLock nuts, using the 13MM wrench. • Install the foot toe pieces to the front pedal arms with two bolts (M8 x 45MM) using the Blue 5MM Allen wrench. BLUE BAG STEP4 • X6000 only: Unfold the RPM sensor wire, located in the frame console mast bracket. Remove any kinks. • All models: Slide the rubber console mast cover onto the bottom of console mast, and slide it up as far as it will go. • X6000 only: Holding the console mast above the frame bracket, guide the RPM sensor wire and lower magnet cable up through the console mast while simultaneously sliding the console mast onto the frame bracket. • All models: Bolt the console mast to the frame bracket with two bolts (M8 x 60MM), two flat washers (8 x 17 x 1.5T), and two lock washers (8 x 15 x 2T). Tighten with the Blue 5MM Allen wrench. Slide the rubber console mast cover back down over the bolt heads. X6000 NOTE: Be sure the RPM sensor wire exits through the small slot at the top right side of the the console mast. • X6000 only: Mount console to console mast, using the two screws. Plug the RPM sensor wire into the back of the console, and feed the excess back down into the small slot in the console mast. • X6000 only: Turn the tension knob to Level 15. Reach inside the console mast and connect the magnet cables. Turn the knob to Level 1 and mount the knob using a bolt (M5 x 25MM). • X6200 only: Remove the four screws from the back of the console. Plug the wire connector from inside the mast into the console. The cable connector is slotted, so it may only be connected one way; do not force it! • X6200 only: Mount the console to the mast using the four screws. Do not pinch the cable! • All models: Bolt the water bottle cage to the console mast using the two bolts located in the mast. PINK BAG STEP4 OR X6200HRC/DA X6000DA 6 621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 .2000 Vision Fitness. All Rights Reserved. 8.00 Part #Z60EP08-AG1801PRD AG18.01PRD REV1 the vision to succeed STEP5 7 STEP5 • Slide a large spring washer (M26 x 34 x .3T) onto the console mast ...