Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Box 280 • Lake Mills, WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 ©2008 Vision Fitness. All Rights Reserved. May be covered by one or more patents or patents pending: US 4917376 6.08 AG18.42PRD REV6 TOOLS & PARTS INCLUDED HARDWARE INCLUDED HARDWARE INCLUDED 5mm T-Shaped Wrench 15mm/17mm Pedal Wrench Screwdriver PARTS BOX Console Mast Cover Pedals Power Supply Water Bottle and Cage Color Coded Hardware Bags Assembly Guide 14mm Open Ended Wrench 4mm L-Shaped Wrench 5mm L-Shaped Wrench ORANGE BAG M8 x 20L Bolt Quantity: 2 SW8 Lock Washer Quantity: 2 PINK BAG M8 x 15L Bolt Quantity: 6 SW8 Lock Washer Quantity: 8 M8 x 20L Bolt Quantity: 2 BLUE BAG M8 x 25L Bolt Quantity: 2 SW8 Lock Washer Quantity: 4 M8 x 70L Bolt Quantity: 2 M8 x 18 x 1.5T Arc Washer Quantity: 2 M8 x 10L Set Screw Quantity: 1 STEP 2 • Slide the rear foot into place on the frame. Insert two bolts (M8x25L) with two lock washers (SW8) to the outside holes. Insert two bolts (M8x70L) with two lock washers (SW8) to the inside holes. Tighten all bolts with the 5mm T-Shaped wrench. BLUE BAG To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. A s s e m b l y G u i d e E1500 UPRIGHT FITNESS BIKE Rear Foot STEP 2 STEP 3 STEP 3 • Slide the console mast cover onto the console mast. • Wrap the wire tie that exits the bottom of the console mast around the end of the console cable that is resting in the console mast mounting bracket. Pull the wire tie with the wire harness up through the console mast. Slide the console mast over the console mast mounting bracket. Insert three bolts (M8x15L) with three lock washers (SW8) to each side of the mast. Insert a set screw (M8x10L) to the front side of the mast and tighten with the 4mm L-Shaped wrench. Tighten all other bolts with the 5mm T-Shaped wrench. Slide the console mast cover down so that it sits in place on the bike. • Slide the heart rate wires from the handlebar through the hole in the handlebar mounting bracket on the console mast. Pull the wires completely through the hole and set the handlebars into place on the bracket. Secure the handlebars in place with the two bolts (M8x20L) and two lock washers (SW8). Tighten with the 5mm T-Shaped wrench. • Remove the four bolts from the back side of the console. Plug the console cable and heart rate wires into the back side of the console. Place the console onto the mounting plate of the console mast and re-insert the four mounting bolt. Tighten with the screwdriver. • Remove the two bolts from the backside of the console mast. Attach the water bottle cage to the mast with these two bolts. Tighten with the screwdriver. Insert water bottle. PINK BAG Console Console Mast Console Mast Cover Wire Harness Heart Rate Wires STEP 1 • Position the front support tube in place under the mounting plate on the front side of the bike. Insert two bolts (M8x20L) with lock washers (SW8) and arc washers (M8x18x1.5T) into the holes. Tighten with the 5mm L-shaped wrench. ORANGE BAG STEP 4 Seat Post Stud Seat Post Adjustment Knob STEP 4 • Slide the seat onto the seat post stud. Tighten the 14mm nuts on the bottom side of the seat to secure in place. • Slide the seat post into the frame seat post bracket. • Insert the adjustment knob through the seat post bracket and turn to tighten. • Attach left and right pedal straps to left and right pedals. • Attach left and right pedals to left and right crank arms. NOTE: both pedals and crank arms should be labeled left or right. Tighten with the included pedal wrench. • Plug in power supply to power socket on the front side of the bike. SEAT & PEDALS Front Support Tube STEP 1 SIMPLE DELUXE PREMIER CONSOLES STEP 5 • Refer to Product Selection and Model Configuration decal on console or follow these steps. • Once the product is plugged in turn on the console • Select product (Bike (BK) or Elliptical (EP)) using the resistance arrow keys. Press ENTER to select. • Select model number (Bike (1500, 2050, 2250, 3200) or Elliptical (1500, 6000, 6200)) using the RESISTANCE arrow keys. Press ENTER to select. Console will reset to start-up screen. • The product selection and model configuration is now complete. CONSOLE ...