Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
In order to insure our product warranty and to ensure the safe and efficient operation of LifeSpan equipment, only authorized parts can be used. The product warranty is void if any parts, other than those provided by PCE Health and Fitness are used. Exclusions and Limitations • The Warranty does not apply to any defects caused by negligence, misuse, or improper assembly or maintenance. • This Warranty does not apply to discoloration of paint or plastics. • PCE Health and Fitness will not be responsible for incidental or consequential damages. • This Warranty is non-transferable from the original owner. Registration You must register your LifeSpan product before a warranty claim can be processed and proof of purchase must be demonstrated at the time a claim is made. To complete your registration online, go to and fill out the online registration or fill out the warranty card provided with your Rower. Registration cards must be completed and sent to PCE Fitness within 30 days of purchase to activate the Product Warranty on your LifeSpan equipment. PLEASE READ ALL WARNING LABELS PRIOR TO USE Main Contents #2 Sliding rail x 1 #1 Main frame x 1 #4 Middle base stand x 1 #7 #9 Pedal x 2 Seat #19 Display #34 Pedal Axle x 1 #32 Lock pin x 1 O_O) Wrench x 1 Allen key x 2 #33 Carriage Bolt x 2 #49 Washer x 2 #46 Dome Nut x 2 Complete Parts List Part# Description QTY Part# Description QTY 1 Main Frame 1 26 Screw for Rear Stand 1 2 Sliding Rail 1 27 Bolt, Front Pulley 1 3 Rear Suppot Stand 1 28 Bolt, Final Pulleys 2 4 Middle Base Stand 1 29 Bolts for attaching seat 4 5 Left Drive Cover 1 30 Bolt, Seat rollers/stops 5 6 Right Drive Cover 1 31 Sleeve, Seat Roller 3 7 Pedal 2 32 Lock Pin 1 8 Resistance System 1 33 Carriage Bolt 2 9 Seat 1 34 Pedal Axle 1 10 Seat Support 1 35 Bolts, Pedals 2 11 Rollers, Seat 6 36 Spacer Sleeve, Pedals 2 12 Pull handle 1 37 Harness, Reed Switch 1 13 End Plugs, Handle 2 38 Screw for cover 7 14 Foam grips 2 39 Screw for cover 3 15 Front Pulley 1 40 Screw for cover 1 16 Pulley, Final Lower 1 41 Screw for Tension Knob 1 17 Pulley, Final Upper 1 42 M8 Nylon Nut 7 18 Tension Knob 1 43 M10 Nylon Nut 2 19 Console 1 44 M1/2 Nylon Nut 1 20 Sensor wire / Reed switch 1 45 M8 Nut 6 21 End Plug for Sliding Rail 1 46 Dome Nut 2 22 Front/Rear Feet 4 47 Cap 2 23 Transport Wheel 2 48 M8 washer (big) 3 24 Front/Rear Seat Stop 4 49 M8 washer (small) 2 25 Plastic cover for wheel set 1 50 M10 washer 4 Exploded View STEP 1: ATTACH SEAT TO SLIDING RAIL a. Remove the 4 Allen Head Screws fro m the back of the seat. b. Place the seat over the seat bracket and tighten all four screws. STEP 2: ATTACH MIDDLE BASE TO MAIN FRAME a. Align the middle base under the main frame bracket. b. Insert the 2 carriage bolts from the bottom. c. Place a washer over the end of the carriage bolt and then tighten the dome nut securely. STEP 3: ATTACH SEAT RAIL TO MAIN FRAME a. Line the seat rail directly behind the main frame and attach the wire connectors coming from the seat rail and main frame. STEP 4: PEDAL ASSEMBLY a. Remove the an Allen screw and washer from one end of the pedal axle. b. Push the end if the pedal axle through the top hole in the frame and the only hole in the rail, with a spacer on one side. Add the spacer and the pedal to the other side. c. Using an Allen Wrench on each end of the axle, tighten the Allen Screw with the washer that was removed earlier. d. Insert locking pin in the lower hole of the main frame while lifting the sliding rail up slightly near the pedal axle. STEP 5: INSERT DISPLAY CONSOLE a. Insert supplied AA battery into the back of display. b. Connect the cable inside the hole in the front of the main frame with the connector on the back of the console. c. Push the display console into the hole in the in the main frame until secure. OPERATION RESISTANCE - To increase the tension turn the adjustment knob to a higher number and to reduce the tension, turn the knob to a lower number. CONSOLE READOUTS - The console will automatically turn on when the Rower is in use. If there is no movement for over 4 minutes the console will automatically turn off. PAGE: Press the “PAGE” button to scroll between functions on the console. RESET: Press the “PAGE” button for 3 seconds to reset all values to zero. □1 01 inn □1 STROKES/MIN COUNTER DISTANCE SPEED TIMER CALORIES PAGE NOTE: Ifthe display is illegible or only partially appears, remove the battery for 15 seconds and replace. Battery should be replaced once a year. FOLDING a. To fold the rower, lift up the sliding rail near the pedal axle to relieve pressure from the locking pin. b. Remove the locking pin. c. Lift the seat rail into the upright position and replace locking pin. V / PLEASE READ ALL WARNING LABELS PRIOR TO USE...