Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Grounding provides a path of least resistance for electric current should the treadmill malfunction. This treadmill comes with an electrical cord with an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not connect other equipment to the surge protector or this could cause permanent damage to your treadmill. This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below. 8 Console Panel Functions There are five display windows on the control panel to provide feedback information. TIME WINDOW TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) SPEED WINDOW SPEED: Indicates MPH (miles per hour) or KPH (kilometer per hour) in .1 increments. CALORIES / DISTANCE WINDOW DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0 CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time INCLINE / PULSE WINDOW INCLINE: Indicates incline in percent of grade 0-10% in 0.5 increments. CENTER BRICKYARD WINDOW Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the change in speed profile across the interval range (1-10) and shows position with a blinking action. In Program mode, the treadmill will display the name of the program selected. This is shown on the left hand side of the window. In Manual mode, the LAP counter will appear in the top center of the window, counting each 1/4 mile lap in sequence of completion (1, 2, 3, etc.). CENTER BRICKYARD INCLINE / PULSE TIME SPEED CALORIES / DISTANCE 9 Program Operation QUICK START / MANUAL MODE 1. Plug into a surge protector outlet. Attach the Safety Key on to the treadmill console. 2. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 3. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered. 4. Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) button. 5. To end your workout, press START/STOP button. Belt will gradually slow to zero. 6. To pause your workout, press PAUSE. 7. To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING. 8. Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting started. First, press the POWER button, then press the ENTER PROGRAM button, the time window will blink. Use the SPEED + or - buttons to select your workout time, then press the ENTER PROGRAM button. The SPEED window will now be flashing. Using the same + or - buttons, select the speed for your workout, then press ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or - buttons to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button. PAUSE POWER INCLINE SPEED ENTER START / STOP 10 Program Operation PROGRAM MODE Plug treadmill into a surge protector outlet. Attach the Safety Key on to the treadmill console. 1. Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. 2. Press POWER button. There will be an eight (8) second delay before data can be entered. 3. There are three (3) pre-set and six (6) semi-custom pre-set programs on this unit. The treadmill includes FATBURN, CARDIO, and WARM-UP programs. Press the PROGRAM button to which program you wish to use. PressENTER PROGRAM. 4. Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, and Warm-up) can be customized in the P1 or P2 mode. Aftermaking the program selection, the Center Brickyard window will read “OP”. The “OP” refers to “originalprogram” and is preset. The program name you select will display in the diode light beside the programname. Press the same program button once more and the Center Brickyard window will read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will besaved for future workouts. 1) The WORKOUT TIME window will blink. Use the SPEED + or – arrows to select your workout time. Press ENTER PROGRAM. 2) The SPEED window will then blink. Use the same + or – arrows to select the speed for your workout. Press ENTER PROGRAM. 3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press ENTER PROGRAM. To start, press the START/STOP button. To access P2 mod...