Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Using the hex key provided, turn the left rear roller adjustment bolt . turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself by moving back toward the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions. WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2) First, turn the treadmill on to run at 1 mph. Using the hex key provided, turn the right rear roller adjustment bolt . turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back toward the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions. WALKING BELT IS SLIPPING DURING USE (Diagram 3) First, unplug the power cord from the surge protector. Using the hex key provided, turn both left and right rear roller adjustment bolts the same distance, usually a . turn, in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to slip. Note: Turning the hex key clockwise brings the rear rollers and belt towards you. Turning the hex key counter clockwise pushes the rear roller and belt away from you. Diagram 1 Diagram 2 Diagram 3 21 Maintenance Instructions WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector. CLEANING: Routine cleaning of your unit will extend the life of your unit. WARNING! To prevent electrical shock, be sure the power to the treadmill is OFF and the unit is unplugged from the wall electrical outlet before attempting any cleaning or maintenance. AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to remove excess perspiration. USE NO CHEMICALS. WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week. DECK LUBRICATION: The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance. Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, lubrication is needed. Keys Fitness recommends “Lube N Walk” for cleaning and lubricating the treadmill belt and deck. Ask your retailer or call Keys Fitness at 888-340-0482. TO APPLY LUBRICANT TO THE WALKING BOARD 1.) Take foam wand applicator, without lube, and insert it in between the walking belt and deck, exposing the two plastic tabs at either end of thewalking belt. Take both tabs and run the wand back and fort along the entire length of your deck. Remove the applicator and prepare for lubrication. 2) Apply about a dime's worth of lubrication onto the side of the applicator wand hat was not used for removing dirt and debris (step 1). You can add more or less lubricant, depending on your lubrication schedule. 3) Insert the wand between the walking belt and deck, exposing the two white plastic tabs at either end of the walking belt. 4) Take both of the tabs and run the wand back and forth along the entire length of your deck. You are done until your next scheduled lubrication date. 5) Allow the silicone to ‘set’ for one minute before using the treadmill. WARNING: Do not over-lubricate the walking board. Excess lubricant should be wiped off with a clean towel. 22 Error Messages Treadmill Error Messages. Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. The following error codes will be displayed in the console display windows. Safety Interlock Error Messages SI 1 - Safety key missing, replace and try again. SI 2 - Over voltage protection trip. Notify Keys Fitness Customer Service. Other Error Messages E11 -Lack of speed feedback data from belt motor. Attempt calibration. See Calibration Sequence section on page 20 of this Owners Manual for detailed information. E22 - Under Speed condition detected from the belt motor. Attempt calibration. See Calibration Sequence section for detailed information. E33 - Over Speed condition detected from the belt motor. Attempt calibration. See Calibrat...