Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The model number is 831.285250. The serial number can be found on a decal attached to the elliptical glider (see the front cover of this manual for the location of the decal). Before reading further, please look at the drawing below and familiarize yourself with the parts that are labeled. Resistance Knob FRONT BACK LEFT SIDE Pedal Arm Side Shield Pedal Remote Holder Upright Water Bottle Holder (Bottle not included) Handlebar PART IDENTIFICATION CHART Use the chart below to identify the small parts used in the quantity needed for assembly. Note: Some parts assembly. The number in parenthesis below each part may have been pre-attached for shipping. If a part refers to the key number of the part, from the PART is not in the parts bag, check to see if it has been LIST on page 14. The number after the dash indicates pre-attached. M8 x 19mm Button Screw (10)–2 M8 x 63mm Carriage Bolt (49)–4 M5 x 30mm Button Bolt (51)–4 M8 x 38mm Button Bolt (53)–2 M4 x 12mm Button Screw (57)–4 M5 Nylon Locknut (52)–4 M8 Nylon Locknut (50)–8 1/2” Nylon Locknut (35)–2 M8 x 60mm Bolt (56)–2 Pivot Washer (54)–2 Pedal Washer (32)–2 M4 x 19mm Flange Screw (55)–6 Note: Extra parts may be included. 5 6 ASSEMBLY Assembly requires two people. Place all parts of the elliptical glider in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires that you have two adjustable wrenches , a rubber mallet , and the included allen wrench . 1. Identify the Front Stabilizer (18), which is the narrowest Stabilizer. If there are no Stabilizer Endcaps (20) on the Front Stabilizer, push one onto each end. Attach the Front Stabilizer (18) to the front of the Frame (1) with two M8 x 63mm Carriage Bolts (49) and two M8 Nylon Locknuts (50). 2. If there are no Stabilizer Endcaps (20) on the Rear Stabilizer (19), push one onto each end. Attach the Rear Stabilizer (19) to the Frame (1) with two M8 x 63mm Carriage Bolts (49) and two M8 Nylon Locknuts (50). 3. While a second person holds the Upright (2) near the Frame (1), connect the Extension Wire (47) to the Reed Switch Wire (41). Insert the Upright (2) into the Frame (1), being careful to avoid damaging the wires. Make sure that the Frame Bushings (3) are inserted fully into the Frame. Adjust the Upright (2) so that a bolt can be inserted through the center hole in each side. Secure the Upright with two M8 x 38mm Button Bolts (53) and two M8 Nylon Locknuts (50). 20 2 3 1 18 49 20 50 19 20 50 49 2 3 3 50 41 47 50 53 1 1 50 50 1 20 7 5. Identify the Left Pivot Arm (6), which is marked with a sticker that has an “L” on it. Make sure that there are two Pivot Bushings (9) in the Left Pivot Arm. Slide the Left Pivot Arm onto the Pivot Axle (11), making sure that it is oriented as shown. Put a Pivot Washer (54) onto an M8 x 19mm Button Screw (10) and tighten the Button Screw into the Pivot Axle. 6. Insert a Handlebar (12) into the Right Pivot Arm (7). Slide the Foam Grip (13) u...
Эта инструкция также подходит к моделям:Тренажеры - ET 30 (572.73 kb)
Тренажеры - ET 30 (572.73 kb)
Тренажеры - ET 30 (572.73 kb)
Тренажеры - ET 30 (572.73 kb)