Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
The clip should be attached securely to make certain it does not come off. Be familiar with its function and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal operation. Safety Tether Cord Important Operation Instructions 6 ET2 / ET4 5/16.. x1/2.. Button Head Socket Bolt (12 pcs) Lubricant (1pc) Combination M5 Allen Wrench M6 Allen Wrench (1pc) & Phillips Head Screw Driver (1 pc) M5 Speed Nut (6 pcs) 5x 16m/m Screw (6 pcs) Safety Key (1pc) Assembly Pack Check List (ET2 / ET4) 7 ET2 / ET4 !!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. If this strap is not removed properly the treadmill could spring open unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed. To ensure your personal safety during removal of the shipping strap please make sure the treadmill is positioned flat on the ground, in the orientation it would be in if you were using the treadmill. Do not turn the treadmill up on it..s side while removing the shipping strap. This could cause the treadmill..s folding mechanism to spring open. If the end of the Velcro strap (that you need to grab to remove it) happens to be under the treadmill deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to the strap end. Assembly .. STEP 1 Remove all parts from the carton. Locate the left and right frame base covers. Insert six M5 Speed Nuts on the small plates. Install the cover and use six 5 x 16mm Screws to fasten. .. STEP 2 Connect Lower computer cable with Middle computer cable. .. STEP 3 Hand tighten Right and Left uprights into the upright receiving tubes of frame base with eight 5/16..x 1/2.. Button Head Socket Bolts by using the Combination M5 Allen wrench & Phillips head screwdriver. .. STEP 4 Connect Middle computer cable with Upper computer cable. .. STEP 5 Install the Console Support into the Right and Left uprights with four 5/16.. x 1/2.. Button Head Socket Bolts. .. PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED. Assembly Instructions ET2 / ET4 8 ET2 / ET4 Assembly Instructions (ET2 / ET4) 9 ET2 / ET4 Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. .. To Fold The Treadmill: Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it is secured by the locking telescoping tube assembly in center back of running deck. .. To Unfold The Treadmill: Apply slight forward pressure* on the treadmill running deck with one hand. Pull down on the unlocking lever and slowly lower the running deck to the floor. The deck will lower unassisted when it reaches about waist high. *At the rear roller area to relieve pressure on the locking system. The treadmill is equipped with four transport wheels that are engaged when the treadmill is folded. After folding simply roll the treadmill away. Folding Instructions Transport 10 ET2 / ET4 Getting familiar with the control panel ..ET2 Console GETTING STARTED: Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the power switch located at the front of the treadmill below the motor hood. Ensure that the safety key is installed, as the treadmill will not operate without it. When the power is initially turned on, the display will light up and show ODO in the center of the display and a number in the Distance window. This is an odometer reading that shows how many virtual miles the treadmill gone. Then HRS is displayed and a number in the Time window shows how many hours the treadmill has been used. Then VER is displayed and a number in the Speed window shows the current software version of the console. The console will now be in idle mode, which is the starting point for operation. Operation of Your Treadmill 11 ET2 / ET4 QUICK START: After the treadmill is powered on and the safety key is in place simply press the START key. The treadmill will start at the minimum speed of 0.5 mph, the time will count up from zero and all data will begin accrual. You can adjust the speed and elevation manually by pressing the desired speed and elevation buttons or the quick keys. Press stop to end workout. WINDOW DISPLAYS: DISTANCE: Accumulates total workout distance from 0.00 to 99.99 miles (km). TIME: Accumulates total workout time from 00:00 to 99:59. CALORIES: Accumulates the user..s calorie consumption during exercise. Max. Value is 999.9 calories. SPEED: Displays the current running speed from 0.5 mph .. 10 mph. PULSE: Displays your cur...
Эта инструкция также подходит к моделям:Тренажеры - Esprit ET4 (610.12 kb)