Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
If you have additional questions, please call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is 831.297140. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Handrail Upright Storage Latch Key/Clip Circuit Breaker Walking Belt Cushioned Walking Platform for maximum exercise comfort Foot Rail Power Cord BACK RIGHT SIDE Rear Roller Adjustment Bolt Water Bottle Holder (Water Bottle is not included) Towel Rack Accessory Tray Incline Leg Treadmill Mat 4 ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the drawings below to identify the parts used in assembly. Assembly requires the following tools: The included allen wrench and your own phillips screwdriver and adjustable wrench . Handrail Bolt (15)–2 Base Screw/Latch Screw (13)–6 Handrail Washer (16)–2 Handrail Screw (32)–2 Extension Leg Screw (34)–2 1. With the help of a second person, carefully lay the treadmill on its right side. Insert one of the Extension Legs (41) into the treadmill as shown. Make sure that the Base Pad (36) is on the bottom of the Extension Leg. Attach the Extension Leg with an Extension Leg Screw (34). Be sure to push on the head of the Extension Leg Screw while tightening it. Attach the other Extension Leg (41) as described above. With the help of a second person, carefully raise the treadmill to the upright position so the Extension Legs (41) are resting flat on the floor. 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow the instructions in step 2 to lower the treadmill. Position one of the Handrails (2) on the left Upright (14) as shown. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the left Upright and the Handrail. Do not tighten the Handrail Bolt yet. Tighten a Handrail Screw (32) into the lower end of the Handrail. Be sure to push on the head of the Handrail Screw while tightening it. Next, tighten the Handrail Bolt (15). 15 16 14 32 2 2 34 34 41 36 41 36 1 5 3. With the help of a second person, hold the Console Base (6) and the other Handrail (2) near the right Upright (14) as shown. Note: It may be helpful to rest the other side of the Console Base on the left Handrail. Connect the Console Wire Harness (88) to the two plugs on the Upright Wire Harness (26). Refer to the upper inset drawing. Locate the 7 1/2” Wire Ties (10) on the Console Wire Harness (88) and the Upright Wire Harness (26). Slide the Wire Ties against the plugs as shown. Insert the 11 1/2” Wire Tie (55) through the holes in the Wire Ties. Close and tighten the 11 1/2” Wire Tie. Refer to the lower inset drawing. Insert the Wire Harnesses (26, 88) into the Right Upright (14). Note: If necessary, bend the Wire Harnesses into an “s” shape. Route the Console Wire Harness (88) through the notch in the bracket on the right Handrail (2) as shown. Insert the bracket into the right Upright (14). Make sure that the Console Wire Harness is not pinched. 4. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the right Upright (14) and the right Handrail (2). Do not tighten the Handrail Bolt yet. Tighten a Handrail Screw (32) into the lower end of the Handrail. Be sure to push on the head of the Handrail Screw while tightening it. Next, tighten the Handrail Bolt (15). Place the Console Base (6) on the left and right Handrails (2). Attach the Console Base with four Console Screws (13). 5. Attach the Storage Latch (12) to the left Upright (14) with two Latch Screws (13). Be careful not to overtighten the Latch Screws. 6. Remove the backing from the Adhesive Clip (74). Press the Adhesive Clip onto the Upright Base (14) in the indicated location. Press the Allen Wrench (73) into the Adhesive Clip. To protect the floor or carpet, place the Treadmill Mat (92) under the treadmill. 7. Make sure that all parts are tightened before you use the treadmill. 13 6 13 15 16 14 2 32 4 13 12 14 5 73 74 14 92 6 2 14 3 6 26 10 10 55 88 88 26 26 88 14 2 6 OPERATION AND ADJUSTMENT THE PERFORMANT LUBETM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grou...
Эта инструкция также подходит к моделям:Тренажеры - 831.297140 (468.16 kb)