Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Release the button and allow the handle to seat to tighten or loosen an adjustment. C Main frame assembly Large L M handle C Main frame assembly Seat post E 5 1. If necessary, the four outer leveler feet can be adjusted. Turn stabilizer feet clockwise to lower the indoor cycle. Turn stabilizer feet counterclockwise to raise indoor cycle. Leveler Feet Level the Indoor Cycle Move the indoor cycle to where it will be used and level it by rotating the adjustable feet underneath the stabilizers. Leveling the indoor cycle helps ensure a stable and quiet ride and reduces wear on the frame. When adjusted properly, there is no rocking movement from one foot to the other. Lock Nut A B Rear stabilizer Front stabilizer 2. Secure the leveler feet by tightening the lock nuts, with the multi-purpose wrench, flush against the bottom of the rear and/or front stabilizer. 5. Loosen the 6mm bolt and place seat rails within the clamp. Adjust to desired seat placement using 6mm Allen wrench. 6. Secure the plastic end cap to the seat post using two end cap screws with the Phillips screwdriver side of the 6mm Allen wrench. Seat post clamp Seat F G 4. Attach seat to seat post clamp. Seat post clamp Seat F G End cap K Seat post E A B Rear stabilizer Front stabilizer 6 If desired, the CycleOps Pro Series indoor cycle can accommodate any standard pedals to personalize the fi t, feel and ride. Install using the pedal manufacturer’s specifi cations. Improper installation can result in damage to the crank. Damage caused by improper pedal installation is not covered under warranty. Attach pedals Right pedal 2. Locate the “R” pedal. This pedal is for the right side of the indoor cycle (chain guard side). Turn the spindle clockwise to tighten. Tighten pedals using the multi-purpose wrench or using a pedal wrench to 300 in-lbs. 3. Locate the “L” pedal. This pedal is for the left side of the indoor cycle (no chain guard side). Turn the spindle counterclockwise to tighten, because this pedal is reverse threaded. Tighten pedals using the multi-purpose wrench or using a pedal wrench to 300 in-lbs. 1. Attach the pedals onto the indoor cycle with the multi-purpose wrench included or a pedal wrench (not included). Each pedal is marked with an “R” or an “L” on the spindle. This mark indicates which side of the indoor cycle the pedal is intended to mount on. This is important because the thread directions are different for each pedal. Left pedal Pedal Set CHAPTER 4: gEnERAl UsE The CycleOps Pro Series indoor cycle is easy to use. Adjust the seat and handlebar to alter the ride position. Adjust resistance to change pace/cadence. 1. Adjust seat position to maximum exercise effi ciency, comfort, and reduce risk of injury. Stop the fl ywheel and dismount the indoor cycle before making adjustments. 3. Turn small L handle counterclockwise to loosen. Move the seat post clamp and seat forward or back, to achieve proper position. Turn small L handle clockwise to tighten. 2. Turn large L handle counterclockwise to loosen. Raise or lower the seat post to the desired height. Turn large L handle clockwise to tighten. Adjust Seat Small L handle N Large L handle M R L 7 1. Adjust handlebar to maximize comfort or duplicate outdoor riding position. Stop the fl ywheel and dismount the indoor cycle before making adjustments. 3. Turn small L handle counterclockwise to loosen. Move the handlebar forward or back to achieve proper handlebar position. Turn small L handle clockwise to tighten. 2. Turn large L handle counterclockwise to loosen. Raise or lower the handlebar post to the desired height. Turn large L handle clockwise to tighten. Adjust handlebar N M Small L handle Large L handle Control Resistance (100 pro, 200 pro, 300 pro only) The CycleOps Pro Series indoor cycle allows the user full control over resistance by adjusting the resistance knob. Lower resistance levels enable the pedals to turn at a faster (less diffi cult) pace/cadence. Higher resistance levels enable the pedals to turn at a slower (more diffi cult) pace/cadence. Adjust Resistance (400 pro only) Pedaling resistance is automatically controlled by the Joule display, located on the handlebar. Reference the Joule user guide for more information. 3. In case of emergency or before dismounting the indoor cycle, press directly down on the resistance knob to bring the fl ywheel to an abrupt stop. 1. Control pedaling resistance by using the resistance knob located behind the handlebar on the top tube of the main frame assembly. 2. Turn the knob clockwise (+) to increase resistance. Turn the knob counterclockwise (-) to decrease resistance. 8 CHAPTER 5: Common AdJUsTmEnTs Replace Speed Sensor Battery (200 Pro only) Over time, the lithium battery in the speed sensor will need to be changed. See Preventative Maintenance for when to replace. 1. Using a 4mm Allen wrench, remove the three chain guard bolts and remove the chain guard. 3. Replace the battery with a compatible CR2032. Replace Cadence Sensor Battery ...
Эта инструкция также подходит к моделям:Тренажеры - 200 PRO (7.2 mb)
Тренажеры - 300 PRO (7.2 mb)
Тренажеры - 400 PRO (7.2 mb)