Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Secure with three screws (M8x15) and three lock washers (M8). Tighten with the 5mm T-shaped wrench. • Slide the seat rail sleeve into posi- tion at the front of the seat rail. BLUE BAG • Slide the seat rail sleeve onto the seat rail. • Connect the heart rate wires com- ing from the seat rail to the heart rate wires coming from the seat frame bracket. Tuck the excess wire under the seat frame bracket. • Slide the seat rail onto the seat rail bracket. Secure with three screws (M8x15) and three lock washers (M8). Tighten with the 5mm T-shaped wrench. • Slide the seat rail sleeve into posi- tion at the front of the seat rail. BLUE BAG 2STEPFrame Bracket Seat Rail Sleeve 6 3STEP• With four screws (M8x15) and four lock washers (M8) attach the seat han- dlebar to the seat frame. • Connect the heart rate wires coming from the seat handlebar to the heart rate wires on the seat frame. • Mount the backrest and the seat cushion to the seat frame using eight screws (M6x35) and eight arc wash- ers (M6). Tighten with the 4mm L- shaped wrench. PINK BAG Seat Handlebar 3STEP • With four screws (M8x15) and four lock washers (M8) attach the seat han- dlebar to the seat frame. • Connect the heart rate wires coming from the seat handlebar to the heart rate wires on the seat frame. • Mount the backrest and the seat cushion to the seat frame using eight screws (M6x35) and eight arc wash- ers (M6). Tighten with the 4mm L- shaped wrench. PINK BAG Seat Handlebar 3STEP 7 8 STEP 4 • Slide the mast cover onto the console mast. • With the included wire tie, pull the console cable, or sensor wire, and heart rate wires, through the console mast. Place the console mast into the console mast mounting bracket. Secure the mast to the bracket with five screws (M8x15L) and four lock washers (M8) and tighten with the 5mm T-shaped wrench. NOTE: The screw facing the seat does not use a lock washer. Tighten this screw until snug. Slide the console mast cover down over the screw heads. • R2000 ONLY: Turn the tension knob to level 16. Direct the cable on the tension knob through the tension knob bracket. Attach the cable to the tension cable located in the console mast. Secure the tension knob to the console mast with the washer (M5) and screw (M5x65L). Tighten with the screwdriver. • Remove the four screws from the back of the console. Plug the wire harness and heart rate wires into the console. Mount the console onto the console mast with the four screws. • R2000 ONLY: Insert the two AA batteries into the console. • Remove the two M5x15L Screws from the water bottle cage holes on the console mast. • R2000 ONLY: Secure the water bottle bracket to the console mast with the 4mm L-shaped wrench and two cap screws (M5x35L). Attach the water bottle cage to the bracket with two screws (M5x15L) using the screwdriver. Insert the water bottle into the cage. • R2100 ONLY: Attach the water bottle cage to the console mast with two screws (M5x15L) using the screwdriver. Insert the water bottle into the cage. GREEN BAG STEP 4 R2000 R2100 Mast Cover Console Mast Mounting Bracket Waterbottle Bracket STEP 5 • Attach the left and right pedals to the left and right crank arms, tighten using the 15mm pedal wrench. PEDALS 5STEP5STEP• Attach the left and right pedals to the left and right crank arms, tighten using the 15mm pedal wrench. PEDALS 5STEP 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2004 Vision Fitness. All Rights Reserved. 5.05 Part #Z20RB104-AG AG18.17PRD REV5 9 ...
Эта инструкция также подходит к моделям:Тренажеры - R2000 (985.63 kb)