Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Attach the Right Upright (82) to the bracket on the right side of the Base (109) with two 1 1/4” Bolts (104) and two Internal Star Washers (72). (Note: It may be helpful to use a rubber mallet to fully insert the Right Upright into the bracket.) Do not tighten the Bolts yet. Be careful not to damage the Wire Harness. Attach the Left Upright (69) to the left side of the Base (109) in the same way. Note: There is not a wire harness on the left side. 82 83 1 69 Hole 109 104 72 Bracket 6 69 82 113 73 83 71 71 72 72 4 85 83 4. With the help of a second person, hold the Console Base (85) near the Uprights (69, 82) as shown. Connect the Wire Harness (83) to the wire harness in the Right Handrail Bracket (113). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to connect them again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the wires harnesses into the Right Upright (82). Hold the Handrail Brackets (73, 113) on top of the Uprights (69, 82). Finger tighten two 1” Bolts (71) with Internal Star Washers (72) into the Handrail Brackets and the tops of the Uprights as shown. Press the Handrail Brackets towards the center of the treadmill. Then, tighten both Bolts. 7 3. With the help of a second person, carefully tip the Uprights (69, 82) down so the treadmill pivots on the Wheels (108) as shown. Tighten a 3/4” Screw (6) into one side of the Base (109) and one of the Wheel Housings (106). Attach a long Rear Base Pad (105) and a short Front Base Pad (100) to the Base with four additional 3/4” Screws (6) as shown. Repeat this step on the opposite side of the treadmill. With the help of a second person, carefully raise the Uprights (69, 82) to the vertical position. 2. Open part bag C. See drawing 2a. Locate the Wheel Housings (106). Attach a Wheel (108) to each Wheel Housing with a Wheel Bolt (107) and a Wheel Nut (21) as shown. Do not overtighten the Wheel Bolts. See drawing 2b. Insert a Wheel Housing (106) into the Base (109). (Note: It may be helpful to use a rubber mallet to fully insert the Wheel Housing.) Press a Base Endcap (99) onto the end of the Base. Repeat this step on the opposite side of the treadmill. 100 105 105 109 106 106 106 108 21 6 6 106 108 106 99 99 107 107 2a 2b 108 108 109 69 82 3 6 6 100 6 8 6. Identify the Left and Right Handrails (68, 81) (see the end views of the Handrails in the inset drawing). The curved edges of the Handrails should be on the outside. Slide the Right Handrail (81) onto the Right Handrail Bracket (113), and press the lip on the front of the Right Handrail under the Console Base (85). (Note: It may be helpful to tip the Right Handrail and to tap it with a rubber mallet to correctly position it.) Tighten three 3/4” Screws (6) into the Right Handrail as shown. Note: It may be necessary to move the lower end of the Right Handrail slightly to align the lower screw hole. Attach the Left Handrail (68) in the same way. See assembly step 1. Tighten the four 1 1/4” Bolts (104). 113 81 Lip 85 68 6 6 6 7. Press the Latch Knob Sleeve (75) into the Left Upright (69). Note: It may be helpful to use a rubber mallet to fully insert the Latch Knob Sleeve. Remove the Latch Knob (70) from the Latch Pin (80). Make sure that the Latch Pin Collar (76) and the Spring (77) are on the Latch Pin. (Note: If there are two Latch Pin Collars, place one on each side of the Spring.) Insert the Latch Pin into the Left Upright (69) and tighten the Latch Knob onto the Latch Pin. 80 75 76 69 77 7 70 (81) Curved Edge (68) 5. Open part bag A. Hold the Pulse Bar (125) near the Console Base (85). Connect the Pulse Wire (124) on the Pulse Bar to the indicated wire on the Console Base. The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to connect them again. Insert the wires into the hole in the Console Base. Have a second person hold the Pulse Bar (125) firmly on the Console Base (85). Attach the Pulse Bar to the Console Base with two 1 1/4” Screws (92) in the locations shown. Be careful not to damage the Pulse Wire (124) or the wire on the Console Base. Next, tighten two 2” Silver Screws (93) into the Console Base and the Pulse Bar in the locations shown. Note: The correct Screws must be used in the correct locations, or the Pulse Bar may be damaged. 92 85 125 5 92 93 124 93 124 8. Raise the Frame (54) to the storage position. (See HOW TO FOLD THE TREADMILL FOR STORAGE on page 21.) Attach the Left and Right Rear Feet (63, 58) to the bottoms of the Left and Right Rear Endcaps (64, 62) with four 3/4” Screws (6) as shown. Note: There are stickers identifying the Left and Right Rear Feet. Be careful not to overtighten the Screws. 58 66 63 6264 54 8 9. Make sure that all p...