Оценок - , средний балл:
(
)
)
Производитель: Kobe Range Hoods
Размер: 1 mb
Название файла: manaul-IN-027-EN-FR-SP-091209.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
• Use an extinguisher ONLY if: a) You have a Class A, B, C extinguisher and know how to operate it. b) The fire is small and contained in the area where it started. c) The fire department has been called. d) You can fight the fire with your back to an exit. What to Do If You Smell Gas - Extinguish any open flame. - Do not try to turn on the lights or any type of appliance. - Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting. 3) Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities. 4) Activating any switch on may cause ignition or an explosion. 5) Due to the size and weight of this hood, two people installation is recommended. ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes. 3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Liner (Sold Separately) {A} KOBE Range Hood {B} Warranty Registration Card{C} Instruction Manual {D} Aluminum Filter – 2 {A} {B} {C} {D} {E} Liner - FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE OR CONTACT KOBE RANGE HOODS AT (626) 775-8880. 4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TABLE 1. (All calculation in inches.) - FOR UNDER THE CABINET TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36") C = Height of Counter Top to Wood Frame Bottom (Recommended 27" to 30") D = Height of Wood Frame SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. 5 - For Insert installation Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood, if any. • Use duct tape to seal joints between pipe sections. CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. And use a protective covering to protect cooktop and/or countertop from damage. Figure 1 Figure 2 Custom Hood Preparation 1. The custom hood frame must be sized to shape and the weight of the insert. Refer to Measurements and Diagrams on Page 13. 2. It must have a sturdy base (1/2 inch thick plywood recommended) to sustain the weight of insert. 3. If an optional liner will be installed, the side of the wood cabinet must be sturdy (1/2 inch thick plywood recommended). 4. It is recommended to install a rear and front stud support. Refer to Figure 2. The stud supports are located 1-1/2” up from the base of the wood frame. Figure 3 Liner Installation 5. The custom/wood hood must have a sturdy base to accommodate the cut-out for the inset. The base must be recessed to accommodate the height of the liner (See liner dimension on Page 14) 6. Secure the liner to the bottom of the base using screws (not included) appropriate for the size and material of your wood frame. 7. Position the rear section of the liner so that it aligns with the back edge of the custom wood frame. Use a pen to trace the outline of the pre-cut area. Remove the liner and proceed to Hood Preparation Before Installation on Page 6. 8. Install the liner with 5 screws (not provided). 6 Wiring to Power Supply Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 9. Temporarily wire the hood to test for proper operation before installing. If the insert does n...