Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
8. Attach backboard assembly to pole section (11). Install pole cap (43). 42 21 43 21 29 29 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 11 27 P/N 21154401 01/04 10 9. 9. 10. Attach adjustment rod (47) to lower elevator Insert handle assembly through pole tubes (29) using bolt (27) spacer (59) and nut mount assembly as shown. Lock pole (42) as shown. assembly in place at the 10’ (3.05m) mark with pin (55). 55 42 27 29 29 67 6747 P/N 21154401 01/04 11 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2). 12. 12. 3 35 22 4 58 1 2 Tighten nut (35) until flush with end of "T" bolt (2) as shown here. NOTE: 44” FAN MOLDED PLASTIC BOARD ASSEMBLY Corner Location 2 1. Correctly identify each pole section. ONLY THE TOP POLE SECTION (14) IS USED IN THIS ASSEMBLY. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 2. Fit spacer (15) into pawl (19). Then continue to assemble as shown. Tighten completely. 15 15 18 24 23 64 19 17 3. 21 Elevator tube Toward Pole Toward Board Identify elevator tubes (21). P/N 21154401 01/04 13 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolts (20), spacers (5, & 40), and nuts (42) as shown. Tighten completely. 23 40 21 40 20 20 5 5 28 21 19 42 42 4. LEVER BROOM HANDLE It is necessary for all parts to be installed properly for this mechanism to work safely and properly. IMPORTANT!: 23 40 21 40 20 20 5 5 28 21 19 42 42 4. LEVER BROOM HANDLE It is necessary for all parts to be installed properly for this mechanism to work safely and properly. IMPORTANT!: 5. Secure pawl (19) in place with clevis Hook one end of the spring (36) into hole of pin (31) and washers (6) as shown. 6. clevis pin (31). Stretch spring (36) and hook it into the notch of the bracket with pliers. 6 31 6 19 21 23 36 21 WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. P/N 21154401 01/04 14 15 P/N 21154401 01/04 7. Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nuts (8). Tighten completely. 8. 23 8 1 8 7 2 21 42 40 21 21 21 21 40 20 Attach upper elevator tubes (21) to backboard brackets (23) using spacers (40) bolt (20) and nut (42) as shown. 44 23 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 2 P/N 21154401 01/04 16 20 20 41 9. Attach upper and lower elevator tubes (21) to top pole section (14) using bolts (20) and nuts (42) as shown. Attach pole cap (41) as shown. 42 21 21 21 21 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2). 10. 3 35 22 4 58 1 2 Tighten nut (35) until flush with end of "T" bolt (2) as shown here. NOTE: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! FAN MOLDED PLASTIC BOARD ASSEMBLY Corner Location 3. Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ONLY THE TOP POLE SECTION (50) IS USED IN THIS ASSEMBLY. 1. Pole bracket will need to be lightly pressed into backboard ribbing. Be sure to press completely into place. Attach rim(58) to backboard and pole bracket (53) with knob (62), reinforcement bracket (61), and carriage bolt (60) as shown. Tighten knob completely. 2. 50TOP 62 61 KNOB MUST BE TIGHTENED COMPLETELY AND CHECKED FOR TIGHTNESS BEFORE EACH USE. WARNING! MIDDLE BOTTOM PRESS BRACKET (20) INTO PLACE HERE 60 53 BOARD STYLE MAY VARY NOTE: 58 Attach board assembly to pole with carriage bolts (63) and knobs (62) as shown. Install pole cap (41) as shown. 62 63 41 3. 50 P/N 21154401 01/04 17 FAN BACKBOARD ASSEMBLY Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1. 34 8 10 66 P/N 21154401 01/04 18 11. 11. Install net clips. WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. CLIP “ARM” CLIP “BODY” AA9 58 BB CC Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “...