Оценок - , средний балл:
(
)
)
Производитель: Huffy
Размер: 1.27 mb
Название файла: 917827d6-4561-f1a4-71ff-3881c822744a.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. 4 P/N 211689C 05/03 Get to know the basic parts of your basketball system..... FRONT BACK TOP POLE MIDDLE POLE FRONT COVER RIM BOTTOM POLE BASE STRUTS ELEVATOR ASSEMBLY BACKBOARD WHEEL CARRIAGE ASSEMBLY 5 05/03 P/N 211689C Item Qty Part No Description 1 900467 Top Pole Section 1 904811 Middle Pole Section (with Label) 1 903407 Bottom Pole Section 2 900223 Wheel Bracket 2 206940 Axle 2 226403 Wheel 6” 4 206938 Pushnut 1 200117 Base 1 203223 Carriage Bolt, 5/16-18 x 1 1 202662 Hex Bolt, 5/16-18 x 4.5 7 203218 Washer 5/16 1 200188 Rod 3/8 x 5.25 1 202882 EyeBolt 3/8 -16 x 3.75 2 906410 Tank Strut 1 200516 Bolt Cover 1 200123 Upper Pivot Bracket 1 206948 Lower Pivot Bracket 2 900122 Hinge Tubes WARRANTY CARD: 1 200512 Hex Bolt 3/8 -16 x 3.5 Please remember to complete your product 5 203232 Flat Washer 3/8 -3/4 registration form either on-line at: 1 206252 Hex Bolt, 3/8 -16 x 1 or mail-in 17 203100 Flange Nut 5/16 -18 the enclosed postcard. 1 203330 Hex Bolt, 3/8 -16 x 4.5 1 108053 Flipper 1 206600 Elevator Shroud 4 203103 Carriage Bolt, 5/16-18 x 2 1 108055 Height Adjustment Shroud 1 908052 Elevator Adjustment Tube 1 201975 Trigger 1 201973 Handle Right 1 201974 Handle Left 4 204804 Screw, Handle, #10 X 1" 2 900867 Jack Plates 1 207103 Pole Cap 4 908051 Elevator Tube 1 206910 Pole Bracket 9 206340 Nut, Nylock, 1/2 -13 2 203053 Pole Bracket Bolt 5/16-18 x 4 4 202862 Spacer 1.19 long 8 204847 Bolt 1/2 -13 x 9.5 1 201139 Bolt 1/2 -13 x 4.5 8 201682 Spacer 1.88 long 2 203798 Bolt 5/16-18 x 1.5 1 206151 Washer Flat 1 203099 Nut, Nylock, 5/16-18 2 200874 Spacer 2 206360 Bolt 3/8 -16 x 2.625 6 203063 Nut 3/8 -16 Nylock 2 900964 Board Brackets 1 200118 Front Cover 4 265601 Front CoverCarriage Bolts 12 201278 Net Clips 1 204290 Net 2 206219 Base Plug 1 202448 Tie Down Stake 1 201568 Anchor Strap 1 202052 Label Height Adjust 2 240027 Nut, Nylock 1/4-20 1 900426 Gas Strut 1 203092 Bolt 1/4-20 x 1.75 1 201978 Height Label 1 240019 Bolt 1/4-20 x .75 1 108056 Plastic Lever 1 206956 Plastic Disc 2 226401 Wheel 4” 2 201651 Spacer, Plastic, 1/4" Long 2 202274 Spacer, Metal, 3-1/2" Long 1 202273 Spacer, Metal, 5-7/8" Long 6 P/N 211689C 05/03 HARDWARE IDENTIFIER Item #9 (1) Item #7 (2) Item #10 (1) Item #15 (1) Item #11 (7) Item #13 (1) Item #20 (5) Item #19 (1) Item #23 (1) Item #21 (1) Item #22 (16) Item #37 (9) Item #26 (4) Item #32 (4) Item #38 (2) Item #39 (4) 7 05/03 P/N 211689C Item #40 (8) Item #41 (1) Item #42 (8) Item #66 (2) Item #43 (2) Item #40 (8) Item #41 (1) Item #42 (8) Item #66 (2) Item #43 (2) 202052 02/03 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. Rotate handle forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Reattach ground restraint and check system for stability. HEIGHT ADJUSTMENT TO ADJUST BACKBOARD: 1. Grasp handle and squeeze trigger. 2. Raise or lower to desired height. 3. Release trigger. 1 3 2 4 Item #57 (1) Item #47 (2) Item #51 (4) Item #44 (1) Item #48 (6) Item #45 (1) Item #60 (1) Item #46 (2) Item #58 (2) Item #62 (1) 8 P/N 211689C 05/03 SECTION A: ASSEMBLE THE POLES 1. 5" (13 cm) 5" (13 cm) 1 3 2 Correctly identify each pole section. Mark pole sections with tape as shown. TAPE TAPE 2. Wood Scrap 2 1 Bounce middle pole section (2) into top pole section (1) together using a wood scrap as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. Position middle pole so that the warning label is on the same side as the 1/2" (cm) diameter holes of the top pole. IMPORTANT!: 9 05/03 P/N 211689C IMPORTANT! Holes in top (1) and bottom pole (3) sections MUST align to correctly position elevator system toward playing surface. While maintaining alignment, bounce assembly and lower section (3) together as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. 1 2 3 3. WOOD SCRAP (NOT SUPPLIED) TAPE REFERENCE MARK 1/2" (1.27 cm) DIAMETER HOLES OF TOP POLE 1 2 3 3. WOOD SCRAP (NOT SUPPLIED) TAPE REFERENCE MARK 1/2" (1.27 cm) DIAMETER HOLES OF TOP POLE 10 P/N 211689C 05/03 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION 1/2” & 9/16” AND 9/16” & 1/2” AND EXTENSION HARDWARE USED IN THIS SECTION (not actual size) Item #9 (1) Item #7 (2) Item #10 (1) Item #15 (1) Item #11 (6) Item #13 (1) Item #20 (5) Item #19 (1) HAMMER OR MALLET Item #23 (1) Item #21 (1) Item #22 (16) Item #26 (4) 11 05/03 P/N 211689C 1. Insert axle (5) through wheel bracket (4). Secure wheels (65) to axle using pushnuts (7). Careful...