Оценок - 4, средний балл: 4
(
)
)
|
Фото и характеристики Life Fitness 97TE |
Фрагмент инструкции
Please take special note of the following important points prior to choosing a location and beginning assembly of the treadmill… IMPORTANT SAFETY INSTRUCTIONS ! • DO NOT position the rear of the treadmill within 6 feet ( 2 meters ) of the nearest obstruction. The sides of the treadmill should maintain a minimum clearance of 8 inches ( 20 cm ) from the nearest treadmill or other obstruction. • DO NOT locate the treadmill outdoors, near swimming pools, or in areas of high humidity. • DO verify the contents of the delivery carton against the accompanying parts listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed on the back page of this assembly instruction booklet. • Save the shipping cartons in case of return. • DO read the entire Operation Manual prior to attempting to operate this machine, as this is essential for proper use. The Manual explains how to properly use the treadmill and helps you to train your staff effectively. • NE placez PAS l’arriere du tapis roulant dans un rayon de 2 m (6 pi) de l’obstruction la plus proche. Les cotes de l’appareil ne doivent pas se trouver a moins de 20 cm (8 po) du tapis roulant voisin ou de toute autre obstruction. • NE placez PAS le tapis roulant a l’exterieur, pres d’une piscine ou dans des endroits tres humides. • VERIFIEZ si l’emballage contient toutes les pieces de la liste jointe avant de le mettre de cote. Si des pieces sont absentes, contactez l’assistance clientele de Life Fitness au numero indique au dos de cette brochure d’instruction de montage.. • VERIFIEZ si l’emballage contient toutes les pieces de la liste jointe avant de le mettre de cote. Si des pieces sont absentes, contactez l’assistance clientele de Life Fitness au numero indique au dos de cette brochure d’instruction de montage. TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, Torx wrench, 3/4” combination wrench, flat blade screwdriver (or 5/16” nut driver) PARTS DESCRIPTION 1 LEFT UPRIGHT Qty: 1 2 RIGHT UPRIGHT Qty: 1 3 HANDLEBAR (LEFT AND RIGHT) Qty: 2 4 ERGO™ FRONT CROSSBAR Qty: 1 5 LEFT INSIDE HANDLEBAR SHROUD Qty: 1 6 RIGHT INSIDE HANDLEBAR SHROUD Qty: 1 7 LEFT OUTSIDE HANDLEBAR SHROUD Qty: 1 8 RIGHT OUTSIDE HANDLEBAR SHROUD Qty: 1 9 DISPLAY CONSOLE Qty: 1 10 LOWER UPRIGHT COVER (LEFT AND RIGHT) Qty: 2 0017-00101-1265 11 LEFT ACCESSORY TRAY Qty: 1 12 RIGHT ACCESSORY TRAY Qty: 1 13 HANDLEBAR CAP Qty: 2 14 REAR FRAME ENDCAP Qty: 2 15 HANDLEBAR SHROUD SCREW Qty: 6 0017-00101-1770 16 ENDCAP / UPRIGHT COVER SCREW Qty: 6 0017-00101-1772 17 DISPLAY CONSOLE / HANDLEBAR SUPPORT SCREW Qty: 6 0017-00101-1773 18 SCREW GROMMET Qty: 2 0017-00042-0326 19 FRONT CROSSBAR SCREW Qty: 4 0017-00101-1774 20 UPRIGHT MOUNTING BOLT Qty: 4 0017-00101-1778 21 ACCESSORY TRAY SCREW Qty: 8 0017-00101-1780 22 FRONT CROSSBAR NUT Qty: 4 0017-00103-0327 23 LINECORD CLIP Qty: 5 0017-00042-0838 24 UPRIGHT WASHER Qty: 4 0017-00104-0335 25 UPRIGHT PLUG Qty: 2 26 FRONT CROSSBAR GROMMET Qty: 2 1” 2” 3” 4” 5” 15 16 18 23 24 17 28 21 22 19 20 IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. IMPORTANT! NE JETEZ PAS LE KIT D’EXPEDITION PLACE SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT TOUS LES ELEMENTS NECESSAIRES POUR L’INSTALLATION. 1. Remove the four SCREWS (A) securing the FRONT GRILL (B) to the FRAME (C). Remove the FRONT GRILL and set it aside. 2. Remove the four SCREWS (D) securing the MOTOR COVER (E). Lift and remove the MOTOR COVER and set it aside. 3. Locate the LEFT UPRIGHT (#1). Lay the LEFT UPRIGHT across the belt and deck with the notched end near the LEFT UPRIGHT MOUNTING BRACKET (F). 4. Unwrap the CABLES (G) (Main Wire Harness, Coaxial Cable, and Ethernet Cable) leading from the LEFT UPRIGHT MOUNTING BRACKET (F). Feed the CABLES through the LEFT UPRIGHT (#1). Carefully tilt the LEFT UPRIGHT upwards and position the notched end of the LEFT UPRIGHT over the LEFT UPRIGHT MOUNTING BRACKET. With the LEFT TOP MOUNTING PLATE (H) directed forward, slide the LEFT UPRIGHT down over the LEFT UPRIGHT MOUNTING BRACKET and pre-installed BOLT and WASHER until it rests on the FRAME (C). Secure the LEFT UPRIGHT to the LEFT UPRIGHT MOUNTING BRACKET using two BOLTS (#20) and WASHERS (#24). One BOLT and WASHER on the inside of the LEFT UPRIGHT and one BOLT and WASHER on the front side of the LEFT UPRIGHT. Leave the BOLTS loose at this time. NOTE: BE CAREFUL NOT TO DAMAGE THE CABLES (G) WHEN ROUTING THEM THROUGH THE LEFT UPRIGHT (#1) OR WHEN SLIDING THE LEFT UPRIGHT OVER THE LEFT UPRIGHT MOUNTING BRACKET (F). NOTE: BE SURE THE PRE-INSTALLED WASHER IS ON THE OUTSIDE OF THE LEFT UPRIGHT (#1) WHEN SLIDING IT DOWN TO REST ON THE FRAME (C). 5. Locate the RIGHT UPRIGHT (#2). With the RIGHT TOP MOUNTING PLATE (J) directed forward, slide the RIGHT UPRIGHT down over the RIGHT UPRIGHT MOUNTING BRACKET (K) and pre-i...