Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: FIGURE 12 • SECURELY assemble the LEFT & RIGHT LEG EXTENSION HANDLES (16 & 15) to the LEG FRAME (34) using two 3/8 X 3-1/4” BOLTS (91), four 3/8” WASHERS (80), and two 3/8” LOCK NUTS (82). See FIGURE 12. • Slide two HINGE TABS (76) onto the LEG FRAME (34) as shown in FIGURE 12. (NOTE: The “hinge” part of the HINGE TAB should face downward.) 85 86 31 34 94 1/2 X 3” 95 3/8 X 3-1/4” 15 76 34 76 16 80 82 STEP 13: FIGURE 13 15 • SECURELY assemble one 2 X 8” PLATE (17) to the LEG SEAT PAD (102) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 13. STEP 14: • SECURELY assemble the LEG SEAT PAD (102) to the HINGE TABS (76) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 14. FIGURE 14 80 17 102 88 3/8 X 1-1/4” 54 • Apply one 1-1/4” RUBBER BUMPER (54) to the 2 X 8” PLATE (17) as shown in FIGURE 13. • SECURELY assemble one 1/2 X 7-7/8” SPRING PIN (66) to the LEG FRAME (34) as shown in FIGURE 14. 88 3/8 X 1-1/4” 76 34 66 102 80 16 STEP 15: FIGURE 15 • Assemble LEG BACK PAD ADJUST (2) and LEG BACK PAD SUPPORT (3) to the LEG FRAME (34) using one 1/2 X 6-1/2” BOLT (97), two 1/2” FLANGE BEARINGS (70), one 1/2” LOCK NUT (85) as shown in FIGURE 15. (NOTE: Securely tighten, then back nut off 1/4 turn to allow the two parts to rotate freely.) 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the LEG CURL/EXTENSION (32) to the LEG FRAME (34) using two 3/4” FLANGE BEARINGS (71), one 3/4” TAPPED SHAFT (77), two black 3/8” LOCK WASHERS (81), and two 3/8 X 1” BLACK BUTTON HEAD CAP SCREWS (87). (NOTE: Both CAP SCREWS must be tightened at the same time using two allen wrenches.) 3/8 X 1” BUTTON HEAD 87 1/2 X 6-1/2” 97 71 34 77 54 32 2 3 85 70 • SECURELY assemble one 1-1/4” RUBBER BUMPER (54) to the contact point on the LEG FRAME (34) as shown in FIGURE 15. 3/8” BLACK 81 LOCKWASHER 2 60 • SECURELY assemble one 1 X 1” GLIDE (60) to the angle on the BACK PAD ADJUST (2) as shown in FIGURE 15. NOTE: TIGHTEN BOTH AT THE SAME TIME! STEP 16: 17 FIGURE 16 • SECURELY assemble the LEG BACK PAD (103) to the LEG BACK PAD ADJUST (2) and the LEG BACK PAD SUPPORT (3) using four 3/8 X 3-1/4” BOLTS (91) and four 3/8” WASHERS (80). See FIGURE 16. • SECURELY assemble two 4 X 7” ROLLER PADS (41) to the LEG FRAME (34) using one 19-1/4” TUBE (39) and two 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. 3 2 34 79 41 39 103 80 3/8 X 3-1/4” 91 18 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 17: FIGURE 17 • SECURELY assemble two 3/8 X 2-3/4” SPRING PINS (62) to the PAD SLEEVES (33) as shown in FIGURE 17. • Assemble four ROLLER PADS (41) to the PAD SLEEVES (33) using four 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. • Slide PAD SLEEVES (33) over LEG CURL/EXTENSION (32) until the spring pin pops into the holes. (NOTE: PAD SLEEVES should be facing as shown in FIGURE 17.) • Insert two 3 X 2” END CAPS (65) into the ends of the LEG CURL/EXTENSION (32) as shown in FIGURE 17. • SECURELY assemble two 3/8 X 1” BUTTON HEAD CAP SCREWS (87) and two 3/8” LOCK NUTS (82) to the last holes in the LEG CURL/EXTENSION (32) as shown in FIGURE 17. • SECURELY assemble LEG FRAME (34) to the LEG WEIGHT STACK BASE (23) using two 1/2 X 4” BOLTS (96), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85). See FIGURE 17. 84 85 23 79 62 41 33 65 82 32 1/2 X 4” 96 87 3/8 X 1-1/4” BUTTON HEAD STEP 18: FIGURE 18 109 106 • Snap two WEIGHT PLATE BUSHINGS (109) into the top side of all sixty WEIGHT PLATES (106) as shown in FIGURE 18. 34 STEP 19: 19 FIGURE 19 • Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19. • Using EXTREME CARE slide twenty WEIGHT PLATES (106) down over the GUIDE RODS (19) with the the key-hole facing as shown in FIGURE 19. • SECURELY assemble the WEIGHT STACK SHAFT (50) to the HEAD PLATE (53) using one 3/8 X 1-1/4” BOLT (88) and one 3/8” BLACK LOCK WASHER (81). (Note: The bolt hole in the HEAD PLATE (53) should be on top.) • Carefully Slide the HEAD PLATE ASSEMBLY down over the GUIDE RODS (19) onto the weight stack as shown. • Slide two 13/16” SHAFT COLLARS (78) over the GUIDE RODS (19) as shown in FIGURE 19. • REPEAT the above steps to assemble the weight stacks on the PRESS WEIGHT STACK BASE (24) and the LEG WEIGHT STACK BASE (23). (NOTE: Use four WEIGHT STACK CUSHIONS (47) (two per guide rod!) on the LEG WEIGHT STACK BASE (23) as shown in FIGURE 19.) TWO PER SIDE! 107 108 106 50 3/8” LOCK WASHER 81 53 19 78 3/8 X 1-1/4” 88 24 23 25 47 • Apply one set of WEIGHT STACK LABELS - LBS. OR NUMBERED 1-20 (107) (108) to each WEIGHT PLATE (106). See FIGURE 19. TWO PER SIDE ON THIS STACK ONLY! STEP 20: FIGURE 20 20 • Slide the PRESS GUIDE ROD SUPPORT (20) and LEG GUIDE ROD SUPPORT (21) over...