Оценок - 3, средний балл: 4.3 ( )

Производитель: Sears Размер: 857.8 kb Название файла: e69c3108-17d8-4034-94e6-a1c7d97d016e.pdf Язык инструкции:

Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the Cables before resistance is felt, the Cables should be tightened. Insert the Weight Pin (26) under one of the indicated Weights (25). Slack can be removed from the Cables by tightening the 1/4” Nylon Locknuts (2) at the end of the Short Cable (23) (see drawing 1) and at the end of the Long Cable (58) (see drawing 2). To do this you may need to remove the Small “U”-Bracket (67) from the Weight Tube (not shown) or remove the 3 1/2” Pulley (15) from the Long “U”-Bracket (57). Make sure that the Cables are not too tight or the Top Weight (76) will be lifted off the weight stack. Additional slack can be removed by moving the 3 1/2” Pulley (15) to the other hole in the “I”-Brackets (81) as shown in the upper inset drawing. Remove the 3/8” Nylon Locknut (21) and the 3/8” x 2” Bolt (12) from the Cable Trap (66), Pulley and “U”-Bracket. Re-attach the Pulley and Cable Trap. Be sure that the Cable trap is in the proper position and that the Cable and Pulley move smoothly. Slack can also be removed by moving the 3 1/2” Pulley (15) to the other hole in the Long “U”-Bracket (57) as shown in the lower inset drawing. Remove the 3/8” Nylon Locknut (21) and the 3/8” x 2” Bolt (12) from the Cable Trap (66), Pulley and “U”-Bracket. Re-attach the Pulley and Cable Trap. Be sure that the Cable trap is in the proper position and that the Cable and Pulley move smoothly. Note: If a Cable tends to slip off the Pulleys often, the Cable may have become twisted. Remove the Cable and re-install it. If the Cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 2 1 23 67 26 76 25 66 81 12 12 2 57 15 21 6615 2 58 21 23 3/4" Round Inner Cap (34) 1" Round Inner Cap (49) 1" Round Cover Cap (70) 5/16" x 2" Eyebolt (35) 1" Square Inner Cap (65) 1 3/4" Square Inner Cap (44) 2" Square Cover Cap (78) 2" Square Inner Cap (27) 1 1/2" Square Inner Cap (32) 1/4" Flat Washer (10) 5/16" Flat Washer (8) 1" Retainer (69) 3/8" Flat Washer (9) 5/16" x 1 3/4" Bolt (72) 3/8" Nylon Locknut (21) 1/2" x 3/4" Spacer (61) 1/4" Nylon Locknut (2)3/8" Nylon Jam Nut (83) 5/16" x 2 1/2" Carriage Bolt (1)5/16" x 2 3/4" Carriage Bolt (14) 3/8" x 2" Bolt (12) 3/8" x 3 1/2" Bolt (16)5/16" x 2 1/2" Bolt (22)3/8" x 2 1/2" Bolt (7) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (71) 3/8" x 7 1/2" Bolt (59) Cable Clip (53) 1" x 7/8" Plastic Bushing (75) 3/8" x 6" Bolt (60) 5/16" x 2 3/4" Bolt (11) 5/16" x 2 1/4" Bolt (33) 1/2" x 1 1/4" Spacer (73) 1/4" x 2" Carriage Bolt (38) 5/16" Nylon Locknut (3) 3/8" x 3 1/4" Bolt (85) 1/4" x 2 1/4" Screw (24)1/4" x 2 1/2" Carriage Bolt (91) 1/4" x 3/4" Screw (18) 1/4" x 2 1/2" Screw (43) 3/8" x 4 1/2" Bolt (79)3/8" x 4 1/4" Bolt (80) 1" Tap Screw (92) 3/8" x 2 3/4" Bolt (93)3/8" x 2 3/4" Carriage Bolt (94) 1 1/8" x 2 1/2" Plastic Bushing (74) Part List—Model No. 831.159370 R0998A Key No. Qty. Description Key No. Qty. Description 1 6 5/16” x 2 1/2” Carriage Bolt 49 4 1” Round Inner Cap 2 4 1/4” Nylon Locknut 50 5 Long Cable Trap 3 23 5/16” Nylon Locknut 51 1 Press Base 4 1 Butterfly Base 52 1 Chain 1 Stabilizer 53 3 Cable Clip 6 6 “V”-Pulley 54 1 Lat Bar 7 4 3/8” x 2 1/2” Bolt 55 1 Top Frame 8 11 5/16” Flat Washer 56 1 Press Upright 9 3 3/8” Flat Washer 57 1 Long “U”-Bracket 10 1/4” Flat Washer 58 1 Long Cable 11 7 5/16” x 2 3/4” Bolt 59 2 3/8” x 7 1/2” Bolt 12 7 3/8” x 2” Bolt 60 2 3/8” x 6” Bolt 13 2 Seat 61 4 1/2” x 3/4” Spacer 14 4 5/16” x 2 3/4” Carriage Bolt 62 2 Weight Guide 12 3 1/2” Pulley 63 1 Weight Tube 16 1 3/8” x 3 1/2” Bolt 64 1 Weight Tube Bumper 17 1 Press Frame 65 1 1” Sq...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: