Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
You will be prompted to fully tighten all fasteners later. Place the Base Frame (1) on the floor. Cap the Base Frame (1) with the 2" X 3" Rect End Plug (42). Cap the Rear Stabilizer (2) with two 1-3/8” x 3” Rect End Caps (41). Attach the Rear Stabilizer (2) to the Base Frame (1) using two 1/2" x 3" Hex Head Bolts (62), six 1/2" Washers (74) and four 1/2" Nylon Nuts (76) as shown in FIG 1. Cap the Upright (3) with the 2" x 3" Rect End Plug (42). Attach the Bumper (45) to the horizontal tube on the Upright (3). Attach the Pop Pin (56) to the Upright (3). Attach the Stopper (48) to the Upright (3) using the 3/8” x 3/4” Sunken Head Screw (72) as shown in FIG 2. Attach the Upright (3) to the Base Frame (1) using two 1/2" x 3" Hex Head Bolts (62), four 1/2" Washers (74) and two 1/2" Nylon Nuts (76) as shown in FIG 3. assembly instructions -8- ASSEMBLY FIG-3 FIG-1 FIG-2 assembly instructions -9- Step 2: Cap the Rear Upright (4) with the 2" Sq End Plug (43). Attach the Rear Upright (4) to the Base Frame (1) using three 3/8" x 3/4" Hex Head Bolts (73) and three 3/8" Washers (75) as shown in FIG 4. Insert the 1" Bushings (46) into the outer holes in the Base Frame (1) as shown in FIG 5. ASSEMBLY FIG-4 FIG-5 Step 3: Insert both Guide Rods (5) through the Rubber Doughnuts (47) and into the holes in the Base Frame (1) as shown in FIG 6. Carefully stack the Weight Plates (8) one at a time by lifting them to the top of the Guide Rods (5), inserting the weights through the rods and slowly lowering each weight. Attach the Select Rod (6) to the Top Plate (7) using the Top Plate Bolt (71). Insert the Top Plate (7) over the Guides (5) and through the Top Weight Plate (8) then secure with the Select Pin (58) as shown in FIG 7. ASSEMBLY assembly instructions -10- FIG-6 FIG-7 Step 4: Attach the Lat Bar Holder (10) to the Top Frame (9) using two 3/8" x 3" Hex Head Bolts (65), four 3/8" Washers (75) and two 3/8" Nylon Nuts (77). Insert two 1" Bushings (46) and two 1/2" Steel Bushings (52) into the Top Frame (9) as shown in FIG 8. Be sure that the 2” x 3” Rect End Plug (42) is inserted into the Top Frame (9). Slide the Top Frame (9) over the two Guides (5). Align the mounting holes in the Top Frame (9) with the holes in the Upright (3) then secure with the 1/2" x 4" Hex Head Bolts (60), four 1/2" Washers (74) and two 1/2" Nylon Nuts (76). Attach the Top Frame (9) to the Rear Upright (4) using two 1/2" x 3" Hex Head Bolts (62), four 1/2" Washers (74) and two 1/2" Nylon Nuts (76) as shown in FIG 9. assembly instructions -11- ASSEMBLY FIG-9 FIG-8 Step 5: Attach the Adj Back Bracket (11) to the Upright (3) using the 3/8" x 3" Hex Head Bolt (65), four 3/8" Washers (75) and the 3/8" Nylon Nut (77) as shown in FIG 10. Secure the Adj Back Bracket (11) in place using the Pop Pin (56). Slide the EVO Band (82) onto the Back Pad (26). Slide the Back Pad Hinges (13) onto the Adj Back Bracket (11). Make sure the holes are on the bottom then attach the Back Pad (26) to the Back Pad Hinges (13) using two 3/8" x 3/4" Hex Head Bolts (73) and two 3/8" Washers (75) as shown in FIG 11. Insert the Bolster (12) into the sleeve welded on the Adj Back Bracket (11) and secure with the 5/16" Sunken Head Screw (78). Slide two 100 mm Foam Pads (27) onto the Bolster (12). If the Foam Pads (27) are difficult to slide onto the Bolster (12) try applying a small amount of soapy water to the Bolster (12) prior to sliding on the pads. Cap both ends of the Bolster (12) with a 1" End Plug (44) as shown in FIG 12. ASSEMBLY assembly instructions -12- FIG-10 FIG-11 FIG-12 Step 6: Cap the Press Support (14) with two 2" Sq End Plugs (43). Attach two Pop Pins (57) to the Press Support (14). Attach the Press Support (14) to the Top Frame (9) using the 1/2" x 7-1/4" Hex Head Bolt (59) and a 1/2" Nylon Nut (76) as shown in FIG 13. Slide the 1-1/4" Hand Grips (28) onto the Handle Bars (15). If the Hand Grips (28) are difficult to slide onto the Handle Bars (15) try applying a small amount of soapy water to the Handle Bars (15) prior to sliding on the grips. Attach the Handle Bars (15) to the Press Support (14) using one 3/8" x 2-3/4" Hex Head Bolt (66), one 3/8" x 3" Hex Head Bolt (65), four 3/8" Washers (75) and two 3/8" Nylon Nuts (77) for each as shown in FIG 14. ASSEMBLY assembly instructions -13- FIG-13 FIG-14 Step 7: Slide a 1-1/4" Foam Pad (29) onto the left Press Arm (16). If the Foam Pad (29) is difficult to slide onto the Press Arm (16) try applying a small amount of soapy water to the Press Arm (16) prior to sliding on the pad. Insert two 3/4" Bushings (51) into the Left Press Arm (16). Attach the Left Press Arm (16) to the left side of the Press Support (14) using a 1/2" Washer (74) and 1/2" Nylon Nut (76). Secure using a Pop Pin (57) as shown. Follow the same procedure to assemble the Right Press Arm (17) to the Press Support (14). assembly instructions -14- ASSEMBLY assembly instructions -15- Step 8: Cap the Seat Support (18) with a 2" Sq End Plug (43). Attach the Q...