Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
FX20 MOTORIZED TREADMILL Visit us at: 15 ASSEMBLY STEP 6: Attach the Upright Base Cover – Left #2 (18) and Upright Base Cover – Left #1 (17) over the Left Upright (15). Secure using three Plastic Fixing Insert (72) and three M4 x 15mm Screw (70). Attach the Upright Base Cover – Right #2 (19) and Upright Base Cover – Right #1 (20) over the Right Upright (16). Secure using three Plastic Fixing Insert (72) and four M4 x 15mm Screw (70). FX20 MOTORIZED TREADMILL Visit us at: 16 FOLDING INSTRUCTIONS FOLLOW THESE INSTRUCTIONS TO FOLD UP YOUR TREADMILL: Your treadmill can be folded up for space saving storage space. Simply lift the deck up from the rear of the treadmill and fold up until it locks in place. TO PREVENT INJURY BE SURE YOU HAVE A FIRM HOLD WHEN RAISING THE DECK. You will hear a “click” sound as the lock engages. Stand behind the treadmill and lift the deck up. Raise the deck up until the lock engages. FX20 MOTORIZED TREADMILL Visit us at: 17 UNFOLDING INSTRUCTIONS FOLLOW THESE INSTRUCTIONS TO UNFOLD YOUR TREADMILL: To unfold the treadmill for use, begin by standing behind and supporting the deck with your hands. Next release the lock with your foot by stepping on the release lever. TO PREVENT INJURY BE SURE YOU HAVE A FIRM HOLD ON THE DECK BEFORE RELEASING THE LOCK. Slowly lower the deck until it rests securely on the ground. Support the deck and release the lock with your foot. Slowly lower the deck until it rests securely on the ground. FX20 MOTORIZED TREADMILL Visit us at: 18 TRANSPORT INSTRUCTIONS How to fold up the treadmill: Your treadmill can be folded up for space saving storage. To do this follow the instructions here: 1. Start by first folding up the running deck as described on the FOLDING INSTRUCTIONS page in this manual. Remove the lock pin from Transportation Wheel bracket as shown. Then lift the treadmill a little bit up from the end of handlebars. You will see the Transportation Wheel Bracket spring out. Insert the lock pin back to the Transportation Wheel bracket. 2 1 2. Stand behind the treadmill and grab the handlebars. Use the transport wheels to roll the treadmill to a desired position. 3. Once the treadmill is in place step on the Transportation Wheel Bracket to make the wheel back to place. Insert the lock pin back to Transportation Wheel Bracket. Then follow the UNFOLDING and STABILIZER ADJUSTMENT instruction pages in this manual to level the frame to the floor. 2 1 FX20 MOTORIZED TREADMILL Visit us at: 19 COMPUTER OPERATION Safety Key A B START Button INCLINE UP/DOWN Buttons C D SPEED UP/DOWN Button STOP/ENTER Button E F Reference Guide MOTION CONTROL G BUTTONS FUNCTION START – Press to start exercise at initial speed 0.5MPH / 0.8KPH. STOP / ENTER a. Press to confirm program and preset function values setting mode. b. Press to run setting procedure before pressing the START KEY. c. Press to stop exercise during workout time. SPEED UP a. Press to increase exercise speed by 0.1MPH / KPH. b. Hold the button to increase rapid speed by 0.5MPH / KMPH per second and release the button to stop the function. SPEED DOWN a. Press to decrease exercise speed by 0.1MPH / KPH. b. Hold the button to decrease rapid speed by 0.5MPH / KMPH per second and release the button to stop the function. INCLINE UP / DOWN a. Press up or down to change incline level. b. Press to select programs and preset related function value. FX20 MOTORIZED TREADMILL 20 FX20 MOTORIZED TREADMILL 20 COMPUTER OPERATION SAFETY KEY The safety key must be inserted into the slot on the console in order to operate the treadmill. Always insert the safety key and attach the clip to your clothing at your waist before beginning your workout. If you should encounter problems and need to stop the motor quickly, simply pull on the cord to disengage the safety key from the console. To continue operation first turn the power switch to off and set the speed controller to stop. Next turn the power switch to on and reinsert the safety key into the console. ENGLISH / METRIC CONVERSION The treadmill computer display can show METRIC and ENGLISH information. This should be preset for your area by the factory. However, in case that the treadmill needs to be converted between METRIC and ENGLISH readout, please follow the procedure below: Set the POWER SWITCH to ON. Press the START button on the computer and hold it. Insert the SAFETY KEY then release the START button. The computer will sound one short beep and the LCD will show “ML” (English) as the factory setting. Press INCLINE UP/DOWN button to switch between ML and KM (Metric) and press STOP/ENTER button to confirm the setting. The computer will sound a long beep and will return to the POWER ON mode with the new setting. POWER ON Set the POWER SWITCH, located on the base frame, to ON and insert the SAFETY KEY. All LCD figures will light up with a short beep sound then display “0” except the SPEED, ...