Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Next, attach the Console to the Console Bracket with four M4 x 16mm Round Head Screws (101). Be careful to avoid pinching the wire harness. 7 6. Insert the end of the Upper Wire Harness (48) through the rectangular hole in the Console Bracket (4). Attach the Console Bracket to the Upright (3) with four M6 x 20mm Button Screws (77). Orient one of the Upright Covers (17) as shown, and hold it against the Upright (3). Attach the Upright Cover with two M4 x 16mm Round Head Screws (101). Attach the other Upright Cover in the same way. 7. The Console (5) requires four 1.5V “D” batteries (not included); alkaline batteries are recommended. Press the two tabs on the battery cover, and remove the battery cover. Next, insert four batteries into the Console. Make sure that the batteries are oriented as shown by the diagrams inside of the battery compartments. Then, reattach the battery cover to the Console. 5. While another person holds the Upright (3), connect the Upper Wire Harness (48) to the Lower Wire Harness (49). Gently pull the upper end of the Upper Wire Harness to remove any slack, and insert the Upright into the Base (1). Attach the Upright with an M8 x 69mm Button Bolt (80), an M8 Split Washer (90), and an M8 Jamnut (79). Do not tighten the Button Bolt yet; make sure that the Jamnut is in the hexagonal hole in the Base. Next, finger tighten two M8 x 23mm Button Screws (84) with M8 Split Washers (90) into the Base (1). Do not tighten the Button Screws yet. Attach the Water Bottle Holder (22) to the Base (1) with two M4 x 14mm Screws (104). 48 5 3 101 101 6 8 48 17 17 3 101 101 77 77 4 4 Battery Cover Batteries Tabs 7 5 3 80 48 49 22 84 84 90 90 90 104 79 1 5 Wire Harness 9. Identify the Left Handlebar (8) and the Left Upper Body Arm (11), which are marked with stickers. Orient the Left Handlebar (8) and the Left Upper Body Arm (11) as shown. Insert the Left Handlebar into the Left Upper Body Arm. Attach the Left Handlebar with two M8 x 41mm Button Bolts (78) and two M8 Jamnuts (79). Make sure that the Jamnuts are in the hexagonal holes in the Left Upper Body Arm. Attach the Right Handlebar (9) to the Right Upper Body Arm (12) in the same way. 10. Insert the Pivot Axle (74) into the Upright (3) and center it. Apply a generous amount of the included grease to the Pivot Axle. Orient the Left Upper Body Arm (11) as shown, and slide it onto the left end of the Pivot Axle (74). Slide the Right Upper Body Arm (12) onto the right end of the Pivot Axle. Tighten an M8 x 23mm Button Screw (84) with an M8 Washer (88) and a Wave Washer (111) into each end of the Pivot Axle (74). Make sure that the Wave Washers are on the ends of the Pivot Axle. 11. Hold the Left Front Handlebar Cover (18) and the Left Rear Handlebar Cover (19) around the Left Upper Body Arm (11). Attach the Handlebar Covers with three M4 x 32mm Round Head Screws (105). Attach the Right Front Handlebar Cover (20) and the Right Rear Handlebar Cover (21) in the same way. 9 11 8 9 78 79 79 12 78 88 74 84 111 11 Grease 10 88 84 111 3 12 105 11 18 11 20 21 12 19 8 9 13. Apply a thin film of grease to one of the Pedal Leg Axles (32) and to the faces of the two Pedal Leg Bushings (33) in the Left Pedal Leg (14). Next, slide an M8 Washer (88) and a Pedal Leg Cover (31) onto an M8 x 23mm Shoulder Screw (115), and turn the Shoulder Screw a few turns into the Pedal Leg Axle (32). While another person holds the front end of the Left Pedal Leg (14) inside of the bracket on the Left Upper Body Arm (11), insert the Pedal Leg Axle (32) into both parts. Next, slide an M8 Washer (88) and a Pedal Leg Cover (31) onto another M8 x 23mm Shoulder Screw (115), and turn the Shoulder Screw a few turns into the Pedal Leg Axle. Tighten both Shoulder Screws. Repeat this step on the other side of the elliptical exerciser. 14. Lift the latch on the underside of the Left Pedal Leg (14), and set the Left Pedal Leg on the left Crank Bushing Sleeve (43). Release the lever, and make sure that the Left Pedal Leg is securely connected to the Crank Bushing Sleeve. Connect the Right Pedal Leg (not shown) in the same way. See step 5. Tighten the M8 x 69mm Button Bolt (80) and the two M8 x 23mm Button Screws (84). 12. Identify the Left Pedal (13) and the Left Pedal Leg (14), which are marked with stickers. Attach the Left Pedal (13) to the Left Pedal Leg (14) with an M4 x 45mm Screw (108), three M4 x 14mm Screws (104), and four Star Washers (112). Attach the Right Pedal (not shown) to the Right Pedal Leg (not shown) in the same way. 15. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser. Grease 13 115 32 88 31 11 12 14 Latch 14 43 13 14 104 104 112 112 112 112 14 108 12 115 88 33–Grease 31 10 HOW TO USE THE ELLIPTICAL EXERCISER HOW TO FOLD AND UNFOLD THE ELLIPTICAL EXERCISER When the elliptical exerciser is not in use, t...