Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
(113 kg). 3 4 BEFORE YOU BEGIN Congratulations for selecting the new PROFORM® 15.5 S. The PROFORM 15.5 S is an incredibly smooth exerciser that moves your feet in a natural elliptical path, minimizing the impact on your knees and ankles. And the unique PROFORM 15.5 S features adjustable resistance and a simple-to-use console to help you get the most from your exercise. For your benefit, read this manual carefully before you use the elliptical exerciser. If you have questions after reading this manual, please see the back cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual. Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. Pulse Sensor Handlebar Pedal Disc *No water bottle is included Pedal Console Water Bottle Holder* Fan ASSEMBLY Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included hex keys and your own Phillips screwdriver , adjustable wrench , and rubber mallet . As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre- assembled. If a part is not in the parts bag, check to see if it has been preassembled. If a part is missing, call 1-888-533-1333. M10 Split Washer (45)–2 M10 Nylon Locknut (33)–6 M10 Washer (35)–2 M8 Nylon Locknut (38)–4 M8 x 45mm Button Bolt (50)–4 M10 x 27mm Patch Screw (40)–2 M10 x 75mm Carriage Bolt (34)–4M10 x 74mm Button Bolt (7)–2 Wave Washer (69)–2 M8 Split Washer (28)–4 Handlebar Washer (55)–2 M8 x 25mm Patch Screw (56)–2 M8 Washer (71)–4 M4 x 22mm Screw (63)–2 M8 x 52mm Button Screw (27)–4 M6 Bolt Set (25)–2 Large Wave Washer (76)–2 5 6 2. While another person lifts the back of the Frame (1), attach the other Stabilizer (9) to the Frame with two M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (33). 9 34 1 2 33 33 3. The Console (23) requires four 1.5V “D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the elliptical exerciser has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries into the Console. If you do not do this, the console displays or other electronic components may become damaged. Remove the battery cover from the Console, and insert four batteries into the Console. Make sure that the batteries are oriented as shown by the markings on the battery cover. Then, reattach the battery cover. 23 Batteries Batteries Battery Cover 3 1. Identify the Stabilizer (9) which has round Endcaps (21) on the ends. While another person lifts the front of the Frame (1), attach the Stabilizer to the Frame with two M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (33). 9 33 21 21 34 34 1 To make assembly easier, read the 1 information on page 5 before you begin assembling the elliptical exerciser. 4. While another person holds the Console (23) in the position shown, connect the console wire to the Extension Wire (68). Attach the Console (23) to the Upright (2) with the four Console Screws (59) included with the Console. Be careful to avoid pinching the wires. Attach the Water Bottle Holder (29) to the Upright (2) with two M4 x 22mm Screws (63). 4 23 2 59 Console Wire 29 63 68 7 5 1 2 33 Avoid pinching the 73 wires during this step 68 7 45 5. While another person holds the Upright (2) in the position shown, connect the Extension Wire (68) to the Lower Wire Harness (73). Push the Extension Wire (68) and the Lower Wire Harness (73) down into the Frame (1). Slide the Upright (2) onto the Frame. Be careful to avoid pinching the Wires. Attach the Upright with two M10 x 74mm Button Bolts (7), two M10 Split Washers (45), and two M10 Nylon Locknuts (33). Do not tighten the Button Bolts yet. 6. Identify the Left Handlebar (6), which is marked with a sticker. Insert the Left Handlebar into one of the Handlebar Legs (5); make sure that the Handlebar Leg is turned so the hexagonal holes are on the indicated side. Attach the Left Handlebar to the Handlebar Leg with two M8 x 45mm Button Bolts (50) and two M8 Nylon Locknuts (38). Make sure that the Nylon Locknuts are inside of the hexagonal holes. Do not tighten the Button Bolts yet. Insert the Pivot Axle (26) into the Upright (2), and center the Pivot Axle. Apply a generous amount of the included grease to both ends of the Pivot Axle. Turn a Handlebar Spacer (47) so that the small arrow on the Handlebar Spacer is pointing toward the floor, and slide the Handlebar Spacer onto the post on the Left Handleb...