Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Then, insert the Console Bracket (3) into the top of the Upright. Attach the Console Bracket with four M4 x 16mm Screws (84). 4 3 Avoid pinching the Wire Harness (100) during this step Avoid pinching the Wire Harness (100) during this step 2 1 100 78 7878 79 79 84 84 95 100 96 3 5 Wire Tie 2 79 7 8 5. The Console (4) can be operated with four 1.5V “D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the elliptical exerciser has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries into the Console. If you do not do this, the console displays or other electronic components may become damaged. Remove the two screws from the back of the console, and remove the battery cover. Insert four batteries into the Console. Orient the batteries as shown by the markings inside the battery compartment. Then, reattach the battery cover. The Console (4) can also be operated with a regulated 6-volt DC 2-amp power supply (not included). To purchase a power supply, call your local Sears store. To avoid damaging the console, use only a manufacturer-supplied power supply. Plug one end of the power supply into the jack on the Console; plug the other end into an outlet installed in accordance with all local codes and ordinances. 5 6. Tip: Be careful not to pinch the wires during this step. While a second person holds the Console (4) near the Upright (2), connect the console wire to the Wire Harness (100). Attach the Console (4) with four M4 x 16mm Flat Head Screws (94). 6 4 4 2 94 96 94 100 Console Wire Batteries Batteries Cover Avoid pinching the wires during this step Screws 9 8 7. Slide the Console Cover (96) (see the drawing 7 in step 6) upward to the Console (4). Attach the Console Cover with four M4 x 16mm Screws (84). 96 84 84 4 8. Apply a generous amount of the included grease to the Pivot Axle (16). Then, apply a small amount of grease to two Wave Washers (88). Insert the Pivot Axle (16) into the Upright (2). Slide a Wave Washer (88) onto each end of the Pivot Axle. Identify the Left Upper Body Leg (6), which is marked with an “L” sticker. Slide the Left Upper Body Leg onto the Pivot Axle (16). Attach the Left Upper Body Leg with an M6 x 16mm Button Screw (80) and a Large Axle Cover (20). Attach the Right Upper Body Leg (124) in the same way. 80 20 6 88 16 88 124 20 80 2 Grease 9. Attach the Left Pedal (12) to the left Pedal Arm (14) with three M10 x 70mm Button Screws (75), three M10 Split Washers (78), and an M4 x 16mm Screw (84). Repeat this step for the other side of the elliptical exerciser. 9 14 7578 78 12 84 10. Apply a small amount of grease to two Wave 10 Washers (88) and to the axles on a Pedal Arm Axle (21). Identify an Upper Body Leg Spacer (113), which Curved Side has a curved side. Slide a Wave Washer (88) and the Upper Body Leg Spacer onto the indicated axle of the Pedal Arm Axle (21); make sure that the curved side of the Upper Body Leg Spacer is facing away from the Pedal Flat Side Arm Axle. Identify a Pedal Leg Spacer (114), which has a 114 flat side. Slide a Wave Washer (88) and the Pedal Leg Spacer onto the other axle of the Pedal Arm Axle (21); make sure that the flat Grease side of the Pedal Leg Spacer is facing away from the Pedal Arm Axle. Repeat this step for the other Pedal Arm Axle (not shown). 113 Grease 88 88 21 10 11 13. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser. 12 11 12. Identify the Right Upper Body Arm (9), which is marked with an “R” sticker. Orient the Right Upper Body Arm as shown; make sure that the hexagonal holes in the Right Upper Body Arm are in the indicated location. Slide the Right Upper Body Arm (9) onto the Right Upper Body Leg (124). Attach the Right Upper Body Arm with two M6 x 38mm Button Bolts (76) and two M6 Nylon Locknuts (77); make sure that the Nylon Locknuts are inside the hexagonal holes. Repeat this step for the Left Upper Body Arm (8) and the Left Upper Body Leg (6). 77 9 124 76 Hexagonal 6 Holes 8 11. At the same time, insert a Pedal Arm Axle (21) into the Right Upper Body Leg (124) and into the right Pedal Arm (14); make sure that the Upper Body Leg Spacer (113) and the Pedal Leg Spacer (114) are in the indicated locations. Attach the Right Upper Body Leg (124) with an M6 x 16mm Button Screw (80) and an M6 Washer (118). Then, attach the right Pedal Arm (14) with an M6 x 16mm Button Screw (80) and an M6 Washer (118). Repeat this step for the other side of the elliptical exerciser. See step 3. Tighten the four M10 x 20mm Button Screws (79). Tip: Tighten the two Button Screws on the front of the elliptical exerciser before tightening the other two Button Screws. 118 118 124 14 80 80 21 114 113 12 HOW TO USE THE ELLIPTICAL EXERCISER HOW TO MOVE THE ELLIPTICAL EXERCISER Due to the size and weight of the elliptic...