Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
When formatting is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. 5 Saving and Restoring All the Data Set the mode switch to the PGM position. Saving (writing) all the data The comfirmation message is printed. To execute * s 144 @ s 1A l To cancel Restoring (reading) the saved data The comfirmation message is printed. To execute * s 148 @ s 1A l To cancel * The message “ACCESSING CARD” will appear and stay on the display until all data is completely written or read. When writing or reading is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. If you save all the data by using an SD memory card that contains some data, the existing data will be erased and replaced with newly saved data. If you need the existing data, use another SD memory card. 6 Writing and Reading of Programming Data Reading the graphic logo data Set the mode switch to the PGM position. The comfirmation message is printed. To execute * s 145 @ s 1A l To cancel * The message “ACCESSING CARD” will appear and stay on the display until all data is completely read. When reading is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. Writing and reading all the programming data You can write all the programming data in the cash register onto an SD memory card (Writing). The existing programming data in the card will all be replaced with the newly written data at this time. You can also replace the programming data stored in the cash register with those stored in an SD memory card by loading the latter into the cash register(Reading). Set the mode switch to the PGM position. Writing The comfirmation message is printed. To execute * s 141 @ s 1A l To cancel Reading The comfirmation message is printed. To execute * s 147 @ s 1A l To cancel * The message “ACCESSING CARD” will appear and stay on the display until all data is completely written or read. When writing or reading is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. 7 Writing of Sales Data Write all of the existing sales data (daily and periodic totals) onto an SD memory card. You can write the data onto the same card a maximum of 400 times unless the card becomes full. Set the mode switch to the X1/Z1 position. The comfirmation message is printed. To execute * 650 P @ s 1A l To cancel * The message “ACCESSING CARD” will appear and stay on the display until all data is completely written. When writing is finalized, the message “SD FINAL” will be printed. In case an error occurs, a corresponding error message will be printed. OPERATOR MAINTENANCE 1 In case of Power Failure When power is lost, the machine retains its memory contents and all information on sales entries. • When a power failure is encountered in register idle state or during an entry, the machine returns to normal operation after power recovery. • When a power failure is encountered during a printing cycle, the register prints “============” and then carries out the correct printing procedure after power recovery. (See the sample print.) 2 In Case of Printer Error If the printer runs out of paper, the printer will stall, and “PAPER EMPTY” will appear on the display. Key entries will not be accepted. Refer to section 4 in this chapter, install a new roll, then press the lkey. The printer will print the power failure symbol and resume printing. If the print head comes up, the printer stalls, “HEAD UP” will appear on the display. Key entries will not be accepted. Bring the print head back to the correct position, then press the lkey. The printer will print the power failure symbol and resume printing. 3 Cautions in Handling the Printer and Recording Paper Cautions in handling the printer • If you are not going to use the register for an extended period of time, pull the print head release lever toward you so that the print head is set apart from the plate. (head-up position) • Avoid dusty and humid environments, direct sunlight and iron powder (a permanent magnet and electromagnet are used in this machine.) • Use the print head release lever only when necessary. • Never pull the paper when it is in contact with the print head. First release the head with the print head release lever, and then remove the paper. • Never touch the surface of the print head. • Never touch around the print head and the motor during printing or before they have had sufficient time to cool. Cautions in handling the recording paper (thermal paper) • Use only paper specified by SHARP. • Do not unpack the thermal paper until you are ready to use it. • Avoid heat. The paper will color at around 70°C. • Avoid dusty and humid storage places. Avoid direct sunlight. • The printed text on the paper can discolor under conditions of high humidity and temperature, exposure to di...