Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Welch Allyn Medical Diagnostic Equipment, модель SCANTEAM 6980

Производитель: Welch Allyn Medical Diagnostic Equipment
Размер: 93.82 kb
Название файла: 69758b02-123a-479e-b5b0-5841a1cd4380.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Please consult factory for availability. & When included, the power pack is a wall mount device with 110 vac primary, and a regulated +5 VDC secondary output. + Connector contains a molded-in power jack. ^ Power must be supplied on pin 9 of the DB-9 connector. SCANTEAM 6980 User’s Guide 3 Installation All versions of the SCANTEAM 6980 depend on an external source of +5 VDC power to operate. Since most RS-232 interface ports don’t provide a power source, an external + 5 VDC power supply must be plugged into the molded receptacle in the SCANTEAM 6980’s interface connector for all versions, except the 6980-5 +. The SCANTEAM 6980 is easily installed into a PC system in the following steps: 1) Turn the system power off. 2) Connect the MSR cable to the PC’s 9 pin D male RS-232 port. 3) Connect the 5 VDC adaptor cable to the MSR and then plug the 5 VDC adaptor into a 120 vac receptacle. 4) The MSR can be mounted to the wall, the side of a PC, a keyboard, or simply to a counter with the hook and loop fastener strips included with the product. Alternatively, the screws holding the bottom plastic case on the MSR may be replaced with longer screws for mounting purposes. 5) Turn the system power on. 6) Configure your host device to accept RS-232 data on its RS-232 port. 7) Test the SCANTEAM 6980’s host interface configuration by passing a magnetic stripe card through the SCANTEAM 6980. The magnetic stripe data should appear on your PC screen. If the data does not appear on the screen, you may have to modify the output data configuration of the SCANTEAM 6980 (see page 6, Configuration Options). + The SCANTEAM 6980-5 will only operate when the host device supplies power on pin 9 of its DB-9 RS-232 interface port. 4 SCANTEAM 6980 User’s Guide Output Data Format Note: See DIP Switch Feature Selection chart on page 8 for factory default settings. Character Frame: Start Bit: One Data Bit: 8, 7 (optional) Parity: None, Odd, Even (optional) Stop Bit: One Single Track: {STX} {SS} {ES} {CHECKSUM OF DATA} {ETX} Dual Track: Track 2 data follows track 1 data or precedes track 3 data. {STX} {SS} {ES} {CHECKSUM} {DLE} {STX} {SS} {ES} {CHECKSUM} {ETX} Triple Track: Track 1 data followed by track 2 data, and then track 3 data. {STX} {SS} {ES} {CHECKSUM} {DLE} {STX} {SS} {ES} {CHECKSUM} {DLE} {STX} {SS} {ES} {CHECKSUM} {ETX} Where: = START OF TEXT CHARACTER = DATA LINK ESCAPE CHARACTER = END OF TEXT CHARACTER SS = Start sentinel % Track 1 for ISO, CA DMV, AAMVA ; Track 2 for ISO, CA DMV, AAMVA ; Track 3 for ISO % Track 3 for AAMVA ! Track 3 for CA DMV ES = End sentinel ? Tracks 1, 2, 3 for ISO, CA DMV, AAMVA ISO = International Standards Organization (ISO # 7811) CA DMV = California Department of Motor Vehicles AAMVA = American Association of Motor Vehicle Administrators Data characters in braces, “{},”and not in boldface are optional. SCANTEAM 69S0 User's Guide б Configuration Options: Dip Switch Controlled The SCANTEAM 6980 contains a Dual In-Line Package (DIP) switch pack which is used to configure the operation of the reader. The position of these switches are pre-set by Welch Allyn and normally do not need to be changed by the user, unless the host device’s RS-232 communication parameters do not match the SCANTEAM 6980’s default settings (see page 8). The DIP switches on the SCANTEAM 6980 control the following host interface parameters: “SS” and “ES” characters This parameter allows the “SS” and “ES” characters encoded on the magnetic stripe to be transmitted or not transmitted to the host PC. RS-232 Data Bit and Parity Selection This parameter allows you to change the MSR’s serial RS-232 output parameters for character data bit count and parity. The following selections are available: • 8 data bits and no parity, • 7 data bits and even parity, or • 7 data bits and odd parity. RS-232 Baud Rate Selection This parameter allows you to change the MSR’s serial RS-232 output parameters for baud rate. The following selections are available: • 1200 bps (bits per second), • 2400 bps, • 9600 bps, or • 19200 bps. Check Sum Selection This parameter allows transmission of a checksum character (or no check sum) after the track data sent by the MSR. In order to access the DIP switch pack, the DIP switch cover must be removed, exposing the switches. 6 SCANTEAM 69S0 User's Guide Accessing the SCANTEAM 6980 DIP Switch 1. Remove the DIP switch cover (on the bottom of the MSR). DIP Switch Cover SCANTEAM 69S0 User's Guide 7 Dip Switch Feature Selection Parameter Configurations RS-232 Type Setting 8 Bit None Reserved 7 Bit Even 7 Bit Odd Data Bit and Parity (D SW1 ON* OFF ON OFF SW2 ON* ON OFF OFF SS, ES Code Setting Enabled Disabled SW3 OFF* ON RS-232 Type Setting 1200 2400 9600 19200 Baud Rate SW4 ON OFF ON* OFF SW5 ON ON OFF* OFF Check Sum Setting ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории